WRT111SFDB00 Whirlpool Refrigerator - Instructions

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

unplug freg.took everything out.pulled out shelves and pulled out back panel.their was my part i had to replace.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

Removed the six screws holding the bottom access plate found at the rear of the refrigerator. This gives you easy access to the run capacitor that has a retaining clip. Remove the wire clip and pull out the capacitor (it has two quick disconnect terminals). Reverse the process using the new run capacitor to complete the repair.

Turn off power to the frig. Remove the shelves and back brackets from the freezer, then with a 1/4" nut driver remove the nuts holding the rear metal panel in place. Once removed the defrost thermostat is right in front of you. You will have to clip the wires from the old t-stat because they are in a harness. Once clipped, strip the wires back, wire in the new t-stat, add wire nuts and put it all back together. Very easy job to do, works great. Thanks Parts Select, Mike.

remoove all the food and shelves out from the freezer section, remoove the light bulb lens ( 1 phillips screw) remoove light bulb, take out 6 srews on the back panel then slide out through the top with a slight bending curve motion, the bimetal thermostat will be clamped to the evaporator inlet, ( just after the cap tube) snap it off, then cut the wires about 2 inches from the stat, strip the ends about a quarter inch with wire strippers, same on the new stat, then use 16 or 18 gauge butt splices and crimp them , then reassemble in reverse order.

Watched video of repair. Took all drawers and drawer holders out of freezer to acesss back panel. Removed 6 screws from back panel,slid up and out. Cut 2 wires to remove old bi-mtl defroster. splice the wires and attached new bi-metal def.

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.