WRS321CDBM00 Whirlpool Refrigerator - Instructions

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Installed the shelf

Took lower back board off, took part off to expose it so I could see where it was leaking, got part number, ordered it.
Shut off water to frig at wall shut off, unhooked both hoses and plug, hooked new part up, turned water back on. Watched couple days to make sure it wasn't leaking. Vacuumed out back good, which I was amazed didn't really need it, hooked part back in place, replaced back with screws.

I removed the filter from the box I took the old filter out and inserted the new air filter put the cover down and that was it.

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

The holder is held in place with two screws. Once you have it unscrewed you can snap the old sockets out and replace them.

Ordered new sockets and presto, the lights work again.
They just snapped into the holder and the holder went up with two screws.
HINT: I did take a photo of the 4 electrical connectors AND labeled each one with a Sharpie 1, 2, 3, and 4 from left to right.

At first ordered the wrong part. Using the website was difficult to find the correct part, but once I called, it was pretty easy to find the part needed. Part showed up and install was only a few minutes. No more leaking!

Thanks for the help PartSelect!

After finally getting the wright parts sent to me I took out old bin added the parts to the new bin slid it in and I’m done.

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.

Very simple fix, remove 3 screws, two connectors to the old switch

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

It was straight forward enough--removed six screws from the metal cooling coil shield at the back of the freezer compartment and removed the shield. That left the motor and its mounting exposed atop the coil. Removed the electrical leads and popped out the motor and fan. Then I replaced the leads on the new motor, reset it in the mounting and pushed the fan propeller from the old motor on the spindle of the new. Twenty minutes tops.

Open the refirigerator door and push and hold the On/Off button at the top to turn off internal power. Open the freezer door and move the icemaker switch on the right side freezer wall to "off".

To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.

The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet.
Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.

Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.

The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.

Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.

Once the motor module is seated, replace the 3 screws and push the white cover back on.

Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.

Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.

The icemaker should start making ice within 2 hours.

Followed the video instructions.