WRS325FNAE02 Whirlpool Refrigerator - Instructions

Replacement was very easy as new ice maker was identical to the old one. Took about 10 minutes.

a simple replacement

I emptied refrigerator contents and tilted the refrigerator to the right so as to access the metal panel upon which the evaporation tray was resting. The metal panel is on the left side underneath the refrigerator and the evaporation tray is resting on the panel. I removed 4 screws that were holding the metal panel, pressed down on the panel, slid out the old, cracked plastic evaporation tray, inserted the new plastic evaporation tray, raised the metal panel to its original position, replaced the 4 screws, being careful not to pinched the water line that feeds the ice-maker. VOILA! Un-tilt the frig and re-stock it. It took a day for the temperature to stabilize, due to tilting, I think. New tray $45.

Replaced upper cam piece on bottom hinge and also replaced pivot thimble on upper hinge.
No problems, except pivot thimble glued in place. Had to cut up and pull out with pliers. Everything works like new now.

Put new drawer in fridge.

looked up the model #, found your co. & ordered a new one Service was excellent, shipping reasonable; it was a pleasant surprise. I will tell my friends about your co.

The refrigerator would not come back on after the defrost cycle unless I smacked the housing around the controls. Since it would come back on after stricking the housing I knew it must be a sticking relay. I used the exploded drawings from Parts Select to determine how to disassemble the housing. Once the part arrived I swapped it out in about 10-14 minutes. The drawings made the job simple. Thanks Parts Select!!! -neal

I discovered that the freezer was not defrosting automatically and the condenser coil was freezing up blocking the flow of cold air to the refrigerator side. I first replaced the thermostat thinking that it would be an easy fix but needless to say it didn't work. My indicator that it was not a successful repair was the continuing blinking of the filter change light on the control panel. Ultimately I had to replace the control board assembly to solve the issue.

Linkage on the cold-control mechanism in the air diffuser assembly was broken. It was necessary to access the diffuser assembly from both the refrigerator and freezer sides of the unit.
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now.

Water leaking from under refrigerator. Initially believed leak was from filter assembly. Removed filter and shut off water supply but leak appeared at different intervals again. Large puddle of water coming out from under refrigerator. Removed back lower panel and checked for leak, but didn't find any. My wife was also checking for leak and found a crack in drip tray. Only way we could get the drip tray out was to first remove front lower panel, disconnect and remove wiring harness in front of drip tray, unbolt water filter assembly, and unbolt water solenoid unit at rear of refrigerator. Their water lines connect to filter assembly. My wife controlled the water solenoid unit to give me play as I pulled the filter assembly out as much as I could from the front. I could now wiggle the cracked drip tray out from under the filter unit. Replaced drip tray and reinstalled wiring harness, water filter unit w/new filter, and re-bolted water solenoid unit at back of refrigerator. Replaced back lower panel after turning water back on and checking for leaks. Replaced front lower panel.

The reason still had leak after initially turning off water supply was because the drip tray is used to catch the water when refrigerator goes into the defrost cycle. Since the original drip tray had cracked, water only appeared on floor after defrost cycle.

I slipped the shelf onto the brackets that already were on the sides of the refrigerator.

Pulled out the old drawer and put in the new.

I began by replacing the central light board by using a plastic non-marring wedge type tool slipping it between the housing and the retainers to release the latch like catch. Then I removed the lightboard and light cover assembly by depressing the latch like retainers for the two wire connectors. Installation was as simple as snapping the wires into the connectors and then pushing the lightboard and light cover assembly into place. One major note: I learned from a repairman that you cannot resolve the problem by simply replacing the central lightboard. you must replace all three lightboards, the two in the refrigerator and the one in the freezer because unless you can absolutely identify which board is causing the fault, it will continue to cause a problem on the main board and the lights will not work. Replacing the other two boards is the same as the central board. Additional comment to consider: I absolutely fail top see how this design of using three circuit boards for a simple light saves me anything; in fact after only 5 years it has cost me in excess of $400 (or 20% of the original cost of the unit) just in materials for a simple light--absurd, ridiculous design. If it burns out again I will have an appliance repairman install a simple 1950's design switch a small LED bulb which will probably last longer than the unit.

simply slid out old damaged/taped up shelves and slid in the new ones i ordered,

The repair was so simple. I removed the old icemaker in about 3 minutes and unpacked and installed the new one is about 10 minutes. It was literally a matter of removing a few screws! Eady to follow instructions!