W8RXEGMWB03 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Madonna from Washington, NJ
- Parts Used:
- WP2166037
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
lost hinge to door while moving
Just put the hinge on and screwed on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from Port Tobacco, MD
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
Ice maker quit making ice--had to either be a faulty switch in the ice maker or a faulty water valve. I guessed it was the ice maker switch and ended up being correct.
It was exactly as everyone else described--remove old ice maker, unplug, plug in new ice maker, attach new ice maker. 3 screws, 1 plug. My plug was the one on the ice maker not on the refrigerator (ie I used the wiring/plug that was already in the freezer).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from HAVELOCK, NC
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
changed the light bulb still would not work so I figured it was the switch sure enough.
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Bakersfield, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
heating element going bad
I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Doyle from Winchester, VA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker was not working.
On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Linda from Santa Maria, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
ice tray leaking
Super! It was so fast and easy to fix. Receive my kit in three days and save a lot of money not having to have a repairman come and do it!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Hemet, CA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Troup, TX
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
ice maker faulty
removed three screws pluged it in and it was ready to go. I must add That I ordered it one day and received it the next day by fed ex. I could not believ how fast the service was also the new icemaker is working great. I will order any furture parts I need from Parts Select. Also have given your web site ot several other people. Thank you very much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rich from Covina, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker wouldn't work
Ice maker wouldn't eject the ice often enough. After reading a few other stories, I just ordered the universal ice maker from Part Select. All I had to do was remove some of the plastic shrouds from my old ice maker and put them on the new one. I also reused my mounting brackets. The whole job took me 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from Ewing, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
ice maker quit
i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Yorba Linda, CA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Original ice maker quit making ice, leaked water.
Removed the old ice maker (2 screws, about 2 minutes). Read the excellent instructions. Prepped the replacement unit by adding the mount bracket. It plugged straight into the existing fridge wiring harness. Amazing how standardized icemakers are! Total time for a very careful job was under an hour.
It came in the mail, I got home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.
Very nice kit, and economical compared to a new fridge!
It came in the mail, I got home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.
Very nice kit, and economical compared to a new fridge!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Tomball, TX
- Parts Used:
- WPW10190929
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The coating on the mold /heater unit as cracked and some broken off and cause the water to drip down in the Ice trace and form large icicles
I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DENNIS from SOUTH LYON, MI
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice maker went bad
Took the old one out in Two Min's, Replaced with the new one in about the same time.
Had ice within 1 hour
Had ice within 1 hour
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosemary from ALBION, NY
- Parts Used:
- WP2315539
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
My fridge was very warm Temperature was 56 and my son did the work on it for me
My son said it was easy to put in the motor I didn’t need the fan my fan was in good shape yet thank you so much for everything
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Alfred from CANTERBURY, CT
- Parts Used:
- 4317943
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker did not make ice
Ordered new ice maker from this site . Installation was very easy. Was happy to see that many electrical plugs were included. Chose the correct electrical plug and installed in 30 minutes. One note, be patient as it takes a while for ice maker to produce ice. When I heard the sound of ice dropping in the bin, I was very happy. Just in time for summer cold drinks. :)
Was this instruction helpful to you?
Thank you for voting!