5VET0WPKLQ03 Whirlpool Refrigerator - Instructions

Open the door. Removed two screws holding the cover of the thermostat. There is a clip which holds the thermostat in place. Remove the clip. Take out the thermostat. Remove the thermocouple (the long grey metal with the coil at the end) which is also held in place by a clip. Replace with the new thermostat and thermocouple and clip into place. Replace the screws to the cover. Close the door.

I used a flat-head screwdriver to pop out the old light rocker switch. Then, I unplugged the wires, plugged them into the new light rocker switch, and then popped the new switch into the hole. That's it! Lights began working again.

First I removed the old lightbulb from the socket and replaced it with a new one to confirm that the bulb was not the problem. I then pryed the socket out with a flat-head screwdriver. I could tell that the socket was anchored in its hole with clips so it was relatively easy to pry it out. Once the socket was out, I disconnected the lead wires and ordered a replacement socket kit from Partselect. When the new one arrived, I reconnected the lead wires to it, snapped it back into its hole, screwed in a new lightbulb, and presto!! The light was back on with no further problem. Thank you, Partselect!! A $15.00 part saved me what probably would have been at least a $100. service call and heaven knows what the technician would have told me I needed!!!

An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

We took the edge out of the slot and pulled the old one off then put the new one on. Once we got the plastic edge started into the slot it was a breeze. Only took about 5 minutes. We were very pleased with the results.

Definatly a two man job. I suggest you put a pad down to protect your floor. Remove the filter, grill, and bolts per instructions. Everything is straight forward. Move the frame back 1/2 to 1 inch then tilt the frig back on it's side about 4 inches. If the frame doesn't drop down, move it back until the front of the frame comes of the front lip of the frig. Place a block under the frig lip NOT the frame and WATCH YOUR FINGERS. The wheel should be hanging down. Just pull out the pin, replace the wheel (make sure you have it facing the correct way) and tilt back and pull the blocks. Move the frig back in place and replace the bolts. Took me and a buddy less than 30 minutes.

Once I saw the replacement part I understood how to pry out the switch with a small screwdriver. Then just unplug the old one, plug in the new one and pop it into place.

The PartSelect site made it easy to correctly identify the correct part, it was inexpensive, and the shipping was fast.

I'm very pleased!

We just had to find the trick to put it in where it would catch on and the rest was a piece a cake.

You had to put it in the groove where it would catch and snap it in place and the rest went in
pretty easy.

We decided to use our crisper drawers to store sodas. Duh..bad plan. The rail that holds the drawers up cracked in half. So we just had the drawers sitting on the bottom of the fridge. So, I got the new rail THE DAY AFTER I ORDER IT! I just recycled the old one, and slid the new one in. Presto. Perfect fit. Actually, better then perfect. There must have been a defect with my old one, because the new one actually SNAPPED into place, instead if just sitting in the frame. So..I am really pleased.

its not that hard to replace. may need help to tilt fridge on one side so you can get to the bottom to remove wheel.Had to undo all four corner screws/bolts to loosen bottom section and slowly pull out base frame which holds the 4 wheels. this frame is also holding the compressor and fan so be careful.replace wheel and slowly put frame back to position and screw back bolts. pull back fridge to upright position. leave unplugged for a day or two to allow gas to come back to normal level as we had tilted it.plug it back and it works.
thanks
Anoop

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

I ordered the crispers and they came the next day.I took them out of the box and had them installed in about 30 seconds.It doesn't get any easier than that.The lady on the phone was very helpful when I placed the order.The fact that they came the very next day was amazing to me.

plastic warped in ,spaced out and, the socket snapped back in place.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.