ET1MHKXMB02 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- anne from E LONGMEADOW, MA
- Parts Used:
- WPW10421486, WP2156006
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Good Parts, Easy Job
Make sure you order the right parts. The bar needs 2 caps so don't make the mistake of only ordering one. Once you push in the end caps into the retainer bar, gently insert bar into slots on door. Right parts will create a perfect fit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from JAY, VT
- Parts Used:
- W10854037
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original drawer handle had cracked and the crack spread down to the body of the crisper unit.
Took out the old, cracked, crisper unit and removed the white trim piece on the handle so that we could re-use it on the new crisper unit (which, in spite of the $90+ price tag did not come with new trim). The whole thing took 3 minutes to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from BONITA SPGS, FL
- Parts Used:
- W11700559
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
none
install ice maker 2 screws wire harness pluged in done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from MARYLAND HTS, MO
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
freezer (later fridge too) wouldn't stay cold~
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from HELENDALE, CA
- Parts Used:
- WPW10662129
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
freezer would not freeze
inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from MEDIA, PA
- Parts Used:
- WPW10189703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
refrigerator was not cooling
Swapped out evaporator fan motor, solved the problem!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from SACRAMENTO, CA
- Parts Used:
- W11700559
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Installed Ice Maker in Freezer
Installed ice machine components using kit and included instructions. Easy! Ran a copper line from under sink valve to back of refrigerator under the floor. Drilled two holes to run copper line. Plumber turned water off and replaced single valve with a double valve (one line to faucet and the other for the copper line). Installed shut off valve and filter at the other end of copper line. Then stainless hose to refrigerator. Everything went smooth. Double check the factory installed plastic line from the electric valve to the inlet for your freezer. Mine was barely inserted and leaked. I pushed it in all the way and it is fine now... Ice maker works really well! Wish I had done this sooner!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from MEMPHIS, TN
- Parts Used:
- 2159061
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
Rerigerator was leaving a lot of condensation on top shelf in refrigerator.
Removal of the door gasket went quite fast. First i needed a 8mm wrench. That what I didn't have. Got the socket set, not the wrench. Tried adjustable wrench, went slow. I slowly got the bolts out. Putting the gasket on was slow. Then I get to the last corner, was awful for me. I finally get it on. Putting the freezer door back on 1st went crazy. I finally looked on top of refrigerator, saw (3) bolts, removed them, installment went easy from there.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MARK from OJAI, CA
- Parts Used:
- WPW10421486
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The fridge was missing the lower shelf bar on the door
The bar slipped right into a groove on each side and took less than 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Karen from HONESDALE, PA
- Parts Used:
- WP2204605
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The freezer would not stay cold enough to freeze
Part Select made it so easy, they told me to download the video I did and I had it fixed within 15 minutes. Part Select is awesome, they helped me diagnose it and told me what part I needed. I will definitely use them again, and I highly recommend them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regina B from ST MARTINVLLE, LA
- Parts Used:
- WPW10421486
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Missing retainer bar for freezer shelf
Retainer bar was a little long but husband used a saw to make smaller (the part said it was a similar to my model- Maytag no longer made this made) It was perfect -- ow I have a whole new usable shelf!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- asberry from SAINT LOUIS, MO
- Parts Used:
- WPW10189703
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
first a loud noise than noise stopped then the refridg. stop cooling like it should
after finding out what could be the problem I order my part which I got around 3 days unboxed it and replaced it in the freezer component which I had already dismantled made note how I took it off and replaced it in the same way took about 25 to 30 minutes quite easy for me was grateful for the solution and proud of myself after replacing it and it began to work now it's freezing and getting cold as it should Thank you my part store
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jacqueline from LEXINGTON PK, MD
- Parts Used:
- WPW10662129
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
No cold
Like you video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Adam from GLOVERSVILLE, NY
- Parts Used:
- WPW10662129
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Plugged it in.
Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.
Was this instruction helpful to you?
Thank you for voting!