KTRP18KDWH05 Whirlpool Refrigerator - Instructions

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

put the end caps on and slid the trim in place

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

This problem can be caused by 3 different part failures. Timer, thermostat or heater. After contacting a service repair shop I was told that most often it is the thermostat. The cost of the repair would be at least $115. To much for an old refer. So I ordered the part from Partselect for $33. and put it in myself. Step1 cut the power to the refer. Step2 remove ice maker if you have one. Step3 remove base and back panels in the freezer. Step4 the coils were badly frozen so I used a hair dryer to thaw it out. Would have waited a long time for it to thaw out otherwise. Step5 The thermostat is clipped on to copper tubing next to the coils. Unclip it and cut the wires close to the thermostat. Strip the wires and wire nut the new thermostat. Clip it back on to the copper tubing. Put it all back together and start it up. It's over a week know and no problems. Note: We have whirlpool appliances that are over 16 years old. I have repaired the washer, oven, and now the refer with parts from Partselect. Good company. Always received the correct part within about 3 days from ordering. If you are able to do the work yourself you can save big bucks and keep your appliances running longer. Good Luck

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

Looked up the refrigerator model number, found parts break down and ordered wheel assy...thought it was the wrong but wheel size was right...read the instructions (good thing) and found out you had to slide entire bottom panel out 1/2 inch to access a hidden pin...did as the instructions said, slid out the bottom panel, found pin as advertised, removed pin, broken part fell out, replaced the wheel assembly, repinned, slid the bottom panel in (a bit more harder than getting it out), replaced all screws and was completed in about 40 -50 minutes. Good thing it came with instructions!!

Pulled refrigerator away fom wall. Removed cardboard cover at back bottom to reveal fan motor.The space available to remove the motor from the bracket is very limited, so smaller hands will be a plus! Tried to get a nut wrench on motor but there was hardly enough room. Finally was able to use a socket set to remove bolts. I would suggest you spray a solvent on the motor mount bolts and seat them in the new motor first. It was near to impossible to get them started in the mount, without seating them first. The electrical clip that connects to the motor fit on the new motor, so I did not have to splice any wiring. This made the job a little easier. Finally, replaced cardboard cover and moved refrigerator back against the wall. .