ET1MHKXMB06 Whirlpool Refrigerator - Instructions

Removed old gasket. Wiped everything down. Popped in new gasket.
It was a little tedious, but it went in easy enough. Some reviews said the new gasket was kinked and bent. Mine I am happy to say was smooth. Some things are still getting quite cold like vegetables and ginger ale.(almost freezing). But it is way better than it was. Saved us from having to purchase another refrigerator. The fellow who helped me made it easy to order and everything went smoothly. I appreciate the help and patience you provided.
I

rippped the old one off and carfully put the new one on with a flat head screwdriver at an angle as not to rip the new one

Unplug pwr cord ..then chk voltage on refrigerator...go inside refrigerator to upper unit where light is and lower unit dwn bye removing the screw then look for thermostat it's right inside ..remove to 3 wires then install new thermostat the same way....plug unit in to power rotate thermostat cooling setting and listen for compressor to tune on. If all goes well the refrigerator should cycle. ....if not change out control board. Good luck and have fun.

Took the glass shelf out of the fridge in our rental home to clean and it just shattered in our hands. Did a search online and found part select, phoned to make sure I was looking at the correct part, the lady on the phone was very helpful. I ordered the shelf using the next day service as we were returning home to the UK within 3 days so did not want to take the chance of not receiving it before we left. I got the notification the part had been dispatched, the part was delivered early next morning. Took the shelf out the package and placed in the tray, job done!. Great service will definately use again, have book marked the site.

Repair man that looked at it said it was the thermostat and that he would order the part. Waited two weeks with no word, so I ordered the part on line, got it the next day and installed it. The only hard part of the installation was getting to the three screws (located vertically in top of refrigerator section) to remove them. Simple three wire clip on changed unit. Total time took about 5 minutes. Refrigerator started cooling when plugged back in. Unfortunately, cooling again stopped within a day, so the original problem was more extensive than just the thermostat (so much for the service call diagnosis). Thoroughly pleased with part ordering, would do it again.

I connected the handle to the refrigerator door using the screwdriver to attach the 2 screws on top and one screw on the bottom.

Very easy and very little time to complete.

Ordered the new part, it was the perfect size and slipped right on to the existing brackets.

It was very easy. The part make look different online but it was a proper replacement.

Open your door as far as it will go. Line it up with the plastic holder should just slide into place.

I first read the instruction manual then I watched the installation video. My water line to it was 3/8. Went to the local ACE Hardware to purchase a short peace of 1/4 copper tubing and the fittings to connect them together. It makes ice every 55 minutes.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I unplugged the appliance removed the back cover exposing the fan motor.Unplugged the wiring harness from the motor assembly.unbolted the fan motor mounting bracket,and removed. Next I unbolted the fan and motor assembly from the mounting bracket.( I pulled the whole bracket out so it would be easier to reinstall the motor and fan assembly,then reinstalled the bracket with the motor and fan already installed) I installed the bracket assembly with the motor and fan back to its location,plugged the wiring harnessback to the motor. replaced the bask pannel ,and plugged the 110 back in the wall socket

The repair story webpage has some problems. I want to rate it "very helpful" but it showed "not helpful". I am pleased with the order service. It was very hard to find the parts on the web. There are a couple of web sites but only partselect has it in inventory. I ordered it, and it came in within 5 days. Excellent service. Will continue to order parts from this site in the future.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Original handle had broken, and super glue wasn't holding any longer. It's just three screws, two up top and one on the bottom that hold the handle on. The fridge and thus the handle comes in three colors (white, biscuit ,and black) I had to email customer service to find out that white is part no PS330447. I got an absurdly fast reply to my question given it was a Saturday afternoon, so that made it easy.