Models > 7ET21PKXFN00 > Instructions

7ET21PKXFN00 Whirlpool Refrigerator - Instructions

Jump to:

All Instructions for the 7ET21PKXFN00
91 - 105 of 347
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
THOMAS from WILLARD, OH
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
defective light switch
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
David from Hemet, CA
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
3 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
dorotea from staten island, NY
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Light didnt go on
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Christine from WASHINGTON, DC
Parts Used:
819342
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
End cap of fridge door had failed
Simple to unscrew and replace parts
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Barbara from FERN BCH, FL
Parts Used:
WP2218118
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Broken butter door
I popped the new one right in.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James from BUFFALO, NY
Parts Used:
WP2218132K
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Replace meat draw
Came on time, just slide in
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ROGER from GREER, SC
Parts Used:
WP2314549
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken crisper frame
Replaced frame
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Thomas from Roseville, CA
Parts Used:
W11384469
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Door light switch disintegrated
Very simple fix, remove 3 screws, two connectors to the old switch
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kenneth from Neptune, NJ
Parts Used:
819342
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Could not properly open the door wirhout the handle
I Clean the handle both top and bottom. I place the cap in place on the bottom of the handle and tap it in snug with a hammer. I then place the top of the handle back into it's original position and then I screwed the end cap in place at the bottom. EASY !!
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Yafa (and David) from Bothell, WA
Parts Used:
8009
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
Replacing the bulb in the freezer side
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
5 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Evans from Santa Rosa, CA
Parts Used:
WP2195947
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
The trim broke off when my kids yanked a bag out and it got caught in the door trim.
I removed the broken trim. Then I popped off one of the trim brackets, slid the trim in, and reinserted the trim bracket. I took 1 minute to perform. The part was perfect. Ordering was a breeze because there was a good schematic diagram to select the correct part.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from Elkland, PA
Parts Used:
WP2218132K
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken meat drawer
Replaced, fit perfect
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jon from Brea, CA
Parts Used:
819342
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
Refrigeration Door Handle End Cap cracked
The repair was REALLY SIMPLE. I popped off the cap cover from the existing end cap, insert the door handle to the new end cap, screw on the new end cap with a Phillips screw driver, and then push the old cap cover back on. Took less than 10 minutes, if that.
3 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
stu from richmond, VA
Parts Used:
W11384469
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
fridge door switch did not work
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
duncan from HOWELL, NJ
Parts Used:
2159061
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
After 17 years, the old door gasket was split and showing signs of mold
The gasket has an inner lip that fits over the edge of the door plastic liner. The old gasket was removed by pulling it straight out, in the plane of the door. Try not to pull sideways as it could crack the door liner, which gets brittle with age. The new liner had a brown magnetic strip, which holds the door closed, and this fits behind the edge of the door liner. Start on the bottom of the door. A helper is useful to hold the gasket loosely vertical. A flat blade screwdriver can be used to pry away the liner to insert the new seal. Once you have worked in the lower edge, install both sides, and then the top. Some juggling side-to-side may be needed for an exact fit
2 of 2 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the 7ET21PKXFN00
91 - 105 of 347