3EHD261MMWR0 Whirlpool Refrigerator - Instructions

the process was pretty straight forward though the part came without instructions. We were able to replace the part improperly with ease. however, we were not able to get the pieces aligned properly for a long time. We ended up taking the door off many times to try to realign the pieces. After many hours I finally unscrewed the bottom cam while the door was in place. The piece popped into place and all was fixed. Had the part come with directions telling us to do this we would have replaced the cam within 15 minutes!

we read on this site how to run the tube down thru the door but we had some problems. we used tape to put together the old and new hose to snake it down and the old hose pulled apart from the new and was stuck in the hole at the bottom of the door. my husband propped up the door and took the bottom hinge off to get to the hole where the tape was stuck and I was able to get a hold of it to finish pulling it through. I think we had to thick of tape wrapped around the two pieces.

Removed door,layed on floor and worked myself around door. I had soaked gasket in hot water before hand but that did not remove wrinkles that well and made gasket stick out some when finished so had to keep adjusting gasket so door would close and still doing it, otherwise got to open freezer first before closing other door until I can get it adjusted.

Heated new door gasket in clothes dryer for 10 minutes. Moved all food out of door into refrigerator proper. Removed door from refrigerator and laid flat on living room carpet. Placed a tarp over the refrigerator opening. Loosened nuts on door holding gasket in place. Removed old gasket as I went. Inserted new door gasket. Needed to use putty knife to get new gasket seated properly. Re-tightened nuts as I went. Rehung door on refrigerator.

One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!

1. Put pieces of wood under door to support it.
2. Unscrew three screws holding door hinge.
3. Disconnect water line.
4. Unscrew screw holding each cam. One to door and one to hinge.
5 Replace cams.
6. Retrieve plate with threaded holes behind frame that the hinge attaches to.
7. Use thin philips screwdriver through the hinge bracket, shim, frame and screw plate to align it for the other two screws.
8. Replace all three hinge screws.
9. Connect water line fitting.
10. Remove wood for door support.
11. Check door for smooth movement and strong pressure when closed.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!

Just replaced the grill with a new one.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

Followed the video instructions.

We pushed the water return hose up from the bottom of the freezer door then we cut the water hose off then we taped the new water hose to the old one using electrical tape then we pulled and pushed at the same time and ran it back down through the door, be careful when you get to the bottom of the door it might stick a little going through the door , on my first try the tape came off without the new hose coming through. Just run the old one back up through the door and re tape it and try again. The connection at the bottom is just a pull out and push in connection and it won't leak after you push it in.

Remove one 5/16 screw from top hinge cover plate. Trace outline of hinge on top of refrigerator with sharpie, so you will know where to put hinge back. Remove 3 5/16 screws from hinge. Lift door up out of bottom hinge, place on table to be able to work on. Remove one 5/16 screw and upper cam piece from bottom of door and replace with new upper cam piece. Remove one 5/16 screw and lower cam piece from bottom hinge on refrigerator. Replace with new lower cam piece and one screw Set door back in place and reattach top hinge with 3 screws adjust refrigerator door as needed for a nice even gap between freezer and refrigerator doors. Tighten screws down and put hinge cover back on with one screw.