G20EFSB23S10 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Charlie from HARRODSBURG, KY
- Parts Used:
- WP12656105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Broken pin to door
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margie from DERBY, KS
- Parts Used:
- W10436252
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Freezer gasket not sealing.
Watched video on line.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from MOUNT AIRY, MD
- Parts Used:
- WP12656018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
broken plastic on crisper drawer
easy peasy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from Grants Pass, OR
- Parts Used:
- WP12656105
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
I broke the pin that holds the lid that covers pantry at the bottom of the fridg.
I removed the drawers above and the glass shelf, then removedthe screws to remove the broken end cap then reversed the proceedure to install the new part. Was simple to do and it works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Port Aransas, TX
- Parts Used:
- WP12656018
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The pin on the right side of the Deli Drawer full width door broke off
I removed the Deli Drawersvegatable and fruit drawers. Removed the glass panel. Removed the screws holding the Endcap and snapped the old one out. A back panel strip that controls the humidity snapped out. I installed the back panel to the new endcap. Installed the new endcap snapping it in place and used the screws to keep it in place.
It was not difficult and everything fit perfectly. The only thing it takes is a little understanding as to how it all fits together. It took about 20 minutes.
It was not difficult and everything fit perfectly. The only thing it takes is a little understanding as to how it all fits together. It took about 20 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pam from CHINO, CA
- Parts Used:
- WP67005930
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The clear lid on my pantry door cracked
I removed the drawers and glass shelf that are over the pantry drawer as well as the small piece that allows the drawer to pull in and out. Then I simply snapped the old one out, snapped the new one in, replaced everything I had removed and Done! Took less than 10 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from CHIRENO, TX
- Parts Used:
- W11368721
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Right Door Magnet weak, door would not stay firmly closed
Replaced seal on door. Same problem. Went to Lowe's and got several magnetic cabinet door catches. Attached them to the top of the door. (they can be seen sticking up), with the magnet part screwed to the door and the metal plate attached to a small wooden block glued to the top of the body with contact cement. Cost abound $16.
"To infinity and beyond."
"To infinity and beyond."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peggy from WOODSTOCK, GA
- Parts Used:
- W11368721
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old gasket was worn out
Heated new gasket in dryer. Removed old gasket. Took less than five minutes per door and I am 78 years old!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DEBRA from STATE COLLEGE, PA
- Parts Used:
- WPW10171529
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Did not have a ice pan
Ordered and placed in the freezer under ice machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ed from SMITH, NV
- Parts Used:
- WP12656018
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Tab broke off for chiller door.
Easy repair, nothing complicated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee Ann from College Station, TX
- Parts Used:
- W10436252
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Frost on the top edge of the freezer drawer
Put the gasket in the dryer for 15 minutes to warm it up. It fit much better after it was warm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from N SYRACUSE, NY
- Parts Used:
- WP12656018
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Dropped a jar onto the pantry and broke the plastic piece on end cap that moved the drawer lid.
Removed the lid and pantry drawer. Removed crisper drawer on right side and glass shelve. Removed 2 screws on glide. Removed 2 nuts with nut driver. Gently tugged on the pantry end cap and it released from the back wall. Had to rotate about 90 degrees to remove the extension off the back wall so I could remove the thermostat control arm from old piece and put it onto the new piece. Gently removed the thermostat control through a series of squeezing pieces and rotations. Do not force anything. Take your time as you are working with plastic that could break at any moment with force. Replace in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neil from E GRAND RAPID, MI
- Parts Used:
- WP12656018
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Bottom drawer access door hinge pin broke of pantry end cap - right side. The pin(knob) is a molded part of the end cap.
Removed two 1/4" screws from the end cap with the nut driver and removed it. Transferred a few pieces from the old end cap to the new. Reinstalled the new end cap and presto, job complete.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Margate, FL
- Parts Used:
- WP12656105
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
pulling the dairy draw out, a plastic knob broke,that keeps the cover on the draw on tight.
after pulling the draw out. had to remove 3 screws on the left side, pull out one part, and then replaced the broken pin. put everything back in place and it was done.perfect job.saved alot of money. thanks to part-select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KENNETH from STOCKBRIDGE, MI
- Parts Used:
- W11346623
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
ICE MAKER WATER FILTER HEAD REPLACEMENT
AS PER A VERY GOOD VIDEO I FOUND SIMPLY BY SEARCHING FOR THE PART NUMBER. IT MAY HAVE BEEN ON THIS SITE. SADLY, THE PUSHING ON THE CONNECTOR WITH THE 1/2" WRENCH LOOKED A LOT EASIER IN THE VIDEO, OTHERWISE EASY PEAZY AND I HAVE VERY PAINFUL ARTHRITIS IN MY SHOULDERS.
Was this instruction helpful to you?
Thank you for voting!