3WSC19D4AY00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Lexie from Lecompton, KS
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The fly wheel on the dispenser was broken
The video for the repair was very helpful and made the repair go very well. It works just like new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CONYERS, GA
- Parts Used:
- WP2176759
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
The ice dispenser handle wasn't working properly. Sometime when dispenser handle was pressed it didn't dispense ice on the first try.
I installed a Ice Door Kit. It works Great Now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from UPPER ARLNGTN, OH
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Replace water filter
Carefully followed the unit’s manual instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geneva from jennings, LA
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
wouldn't feed ice
auger blade was replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Parrish, FL
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken ice bin auger
After watching a video on you tube, the repair was very simple and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Nova, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch was not working after a repairman had fixed something else
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paula from Rush, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light switch sticking
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from River Edge, NJ
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
exchange of defective light rocker switch
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from Fairport, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light in the refrigerator didn't work
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Irene from Whitehall, MT
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No light in frig
We tried repairing with a new switch which was very easy to install but it didn't fix the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Lawrenceville, GA
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Light switch which turns on the lights when the door opens went out
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lanora from Windsor, MO
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Auger drum broke and wouldn't dispense ice
Read the instructions, watched the video and followed the very clear instructions and lay out.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from Manassas, VA
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Plastic Auger Was Broken - No Ice
Watched youtube video from your site. The video was great and the ice macine works perfectly now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from St. Pete Beach, FL
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broke the arm off the food compartment rocker switch
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Was this instruction helpful to you?
Thank you for voting!