WRS526SIAE00 Whirlpool Refrigerator - Instructions

After pulling the fridge out and removing the dust cover over the lower portion in back of the fridge, I could see water dripping from the inlet valve between the water main to the icemaker and the water dispenser in the door.
1. Unplug the fridge
2. Place a towel under the fridge to absorb any over flow
3. Turn off the water supply to the fridge - this is usually at a tap valve on the cold water line. trace the line from the back of the fridge to find the connection point. In the unlikely event there is not valve at the tap valve or if it is inaccessible, turn off the main water supply. If you have to turn off the main supply turn on a faucet somewhere in the house to bleed the pressure from the line.
4. If the valve is tied to the frame or line , undo the tie or cut the zip tie (in my case)
5. Unplug each electric connector from the old valve to the new one.
6. The water connections are all quick connect so release the intake line by pressing down on the white ring and removing the tube. Press the tube into the new valve.
7. Repeat with each line going to the refrigerator making sure to plug each tube into the same outlet you pulled it from
8. In each case to minimize water coming out of the tube, hold your finger over the end while transferring to the new valve.
9. Verify that all tubing ends are FULLY pressed to the valve
10. Turn the water back on slowly and check for leaks. if some are seen turn water back off and repeat steps 6 thru 9.
11. Plug fridge in
12. Run water from the door faucet to bleed any air out
13. Clean up any spillage
14. Replace dust cover (if present) and replace refrigerator in place
Piece of cake

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

just added new shelf - perfect fit

had my wife install them

I removed the filter from the box I took the old filter out and inserted the new air filter put the cover down and that was it.

Took lower back board off, took part off to expose it so I could see where it was leaking, got part number, ordered it.
Shut off water to frig at wall shut off, unhooked both hoses and plug, hooked new part up, turned water back on. Watched couple days to make sure it wasn't leaking. Vacuumed out back good, which I was amazed didn't really need it, hooked part back in place, replaced back with screws.

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Very simple fix, remove 3 screws, two connectors to the old switch

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.

At first ordered the wrong part. Using the website was difficult to find the correct part, but once I called, it was pretty easy to find the part needed. Part showed up and install was only a few minutes. No more leaking!

Thanks for the help PartSelect!

The holder is held in place with two screws. Once you have it unscrewed you can snap the old sockets out and replace them.

Ordered new sockets and presto, the lights work again.
They just snapped into the holder and the holder went up with two screws.
HINT: I did take a photo of the 4 electrical connectors AND labeled each one with a Sharpie 1, 2, 3, and 4 from left to right.

After finally getting the wright parts sent to me I took out old bin added the parts to the new bin slid it in and I’m done.

simply set the new bin where the old one was.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!