3WSC19D4XB00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ronald from Billings, MT
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench set
non-functioning refrigerator lite switch
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sincerely, Ron Marshall, Billings, MT
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Destin, FL
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light switch would not work
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Flagstaff, AZ
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The light went out
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Geneva from jennings, LA
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
wouldn't feed ice
auger blade was replace
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Parrish, FL
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Broken ice bin auger
After watching a video on you tube, the repair was very simple and easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jose from Katy, TX
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench set
The auger drum had detached from the shaft (broke off).
I removed the external shaft that controls the ice grinder. Its spring loaded so you have to remember how to get it back together. I removed the screws that hold the cover in place. I removed the nylon nut that holds the drum and grinder on the center shaft. I replaced the drum and reversed the procedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lexie from Lecompton, KS
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The fly wheel on the dispenser was broken
The video for the repair was very helpful and made the repair go very well. It works just like new!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from UPPER ARLNGTN, OH
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
Replace water filter
Carefully followed the unit’s manual instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from CONYERS, GA
- Parts Used:
- WP2176759
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
The ice dispenser handle wasn't working properly. Sometime when dispenser handle was pressed it didn't dispense ice on the first try.
I installed a Ice Door Kit. It works Great Now!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jackie from Nova, OH
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Switch was not working after a repairman had fixed something else
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Arlington, MA
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Both light bulbs had been replaced, but lights did not turn on.
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from CORDOVA, TN
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
The ice maker drum was totally broken and would not allow ice to drop and the crush ice mode would not work.
I printed your diagram of the complete assembly for reference when installing the new part. I was able to get the part number from the diagram and ordered it online. I received the new part in 2 days. I removed the ice from the ice maker's bin and kept it in the freezer. I removed the old drum and auger from the ice maker assembly and installed the new drum #4388736. I looked at your diagram to make sure I had all of the blades in their right orientation. After the drum and auger assembly was installed, I placed the ice that I had saved into the ice bin and slide it back into place. I then tested if the assembly would now drop ice and also if it would crush the ice, which i do not use very opten, because I know that using the ice crush mode will prematurely wear the drum assembly. The drum and auger gets much more stress when it is crushing ice. After the icemaker worked flawlessly, I rolled the refrigerator back into its regular position along side the cabinets. I was very pleased with the part and the excellent service that PartSelect.com provided. The price was less than I thought I would have to pay. Also, the company provides most of the individual parts of the ice maker assembly. Normally, when I would shop at a designated Whirlpool distributor, I would have to purchase the entire assembly costing 3 or 4 times higher than the price of the individual part. I, will now, always purchase my parts from PartSelect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Saint Marys, PA
- Parts Used:
- 4388736
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
Wore Out The Auger. Needed Replaced
Did it entirely by myself while my husband was at work
Was this instruction helpful to you?
Thank you for voting!