ED5PVEXWS14 Whirlpool Refrigerator - Instructions

Review the video on parts select. Do this first!

The actual repair took less than 30 minutes, including pulling out the refrigerator, performing the repair, and replacing the refrigerator.

Remove the screws holding the cardboard backing to the bottom rear of the refrigerator. Remove the screws holding the pump in place. Remove the electrical connectors and the water hoses from the pump. I needed the wrench to disconnect and reconnect the main inlet hose. Hook everything back up (the sizes of hoses and connectors are different). Replace the cardboard backing. Done!!

I would use Parts Direct again.

Mine is a simple tale of the missing ice cube dispensor guide. When we moved, the guide was missing so when I built our new home with a kitchen in the basement I wanted to hook up the ice dispensor but when I did, the ice cubes always fell off to one side. I decided to order the misssing part on-line. I ordered it paid for it and then received it the next day-wonderful. Within ten minutes, I was ready to go. Thanks for great service. Rick Davis, Bloomington, IL.

I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.

Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and apply the required force to get it off.

After removing a few screws to get to the drum my husband had it back to working like a charm.This part seems to be better made than the original part in the refrigerator.

Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips driver, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

Excellent fit and installation. The door bins slid right in and created the extra space needed on the shelves.

simply removed wires from the old motor and gently lifted it out by by the metal clips - put the old bracket on the new motor, snapped on the new fan, replaced the wires, reinstalled the shield. All done in about 15 min.

That was due to the evaporator blocked by the ice. Check found the defrost timer is okay. The next thing I can think of is to replace the Electronic Control Board which is installed in the fridge side top compartment. Ply open the face cover, remove the nut and screw that secure the EC Board. Pull out the cable, mount the new card and re-connect. So simple. It is back in order.

Same as everybody else on this post. Real easy. Actually, I just wish I would have done it sooner.

Removed front plastic grill and screws holding the filter in place. Also removed lower back cardboard panel to access water lines. Video on this website told me how to remove water lines from filter, you must depress a collar around the water line while pulling out the water line. Then install the new Water Filter Housing and water lines. The only problems I had was the tight space to work in and one of the water lines was leaking, but pushing the water line in further solved the problem.

Resistance on solenoid for water to ice maker measured low (5 ohms). I assumed the coil insulation had degraded because there was almost a short with such low resistance. Replaced the water inlet valve kit and ice maker filled with water and everything worked great. I had to cut the ends of the hoses because my model use compression fittings and this new valve kit used the push on fittings. No leaks no problems. The cables plugged in the opposite direction from the old valve kit, so I had to re-route the cable a little and create slack by removing from 1 cable clamp.

remove shelves in freezer compartment incl.holders(slide up to remove)
Remove lamp/shield
Remove panel (six phillips screws)
disconnect motor
pull off fan blade
squeeze bracket holding motor to remove
remove motor.
Re-assemble (in reverse)

Removed catch tray and then removed two screws that are underneath. I left the control panel hanging from its wires, then removed the two screws from the control bracket.
A word of caution before next step: You need to remove the two micro switches on the left and right. While trying to remove one, it split apart and the pieces fell out. I was able to put it back together and it worked fine. So be careful with the micro switches.
Continue tranferring wires and switches to the new bracket and reassemble in the opposite order.
An easy repair.

remove the front cover. everything else is a quick disconnect type of connection. Nothing to it! I would remove the cover and check these connections anytime the dispenser does not work. Look for broken or disconnected switches. This reapir took me a couple of minutes whereas the repair guy wanted almost 200 bucks to do this job. Parts ran around 30 with shipping.