GX2SHBXVQ04 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Christina from Orange, CT
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the rail to hold the crisper drawers broke
I first removed the bottom shelf. Then I popped the rail in. It was pretty easy although I did have to use some force to fit it in. Ordering the part and doing it myself was a lot cheaper than calling the repair man.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CRESCO, PA
- Parts Used:
- WPW10671238, WP12227303WD
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Center crisper rail breaking off.
After the original center crisper drawer slide rail broke and and second also looking in deep into your parts catalog I discovered that the refrigerator never came with a crisper frame brace from the store or factory.
Thanks to you , I no longer have the use of the center rail breaking off for now everything is made out of cheaply make plastic by whirlpool.
Thanks to you , I no longer have the use of the center rail breaking off for now everything is made out of cheaply make plastic by whirlpool.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry from WARMINSTER, PA
- Parts Used:
- W11396033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken light switch
Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from BLOOMINGTON, IN
- Parts Used:
- WPW10371194
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
needed a Door Bin to replace the old one
just pop the old one out popped the new one in its replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rose from OCOEE, FL
- Parts Used:
- 67003900
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken clips on old part
Snapped in new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANA from ASHTABULA, OH
- Parts Used:
- WPW10671238
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Center Crisper Rail Broke Off At One End--Drawers Would Not Slide And Hang Right.
Very easily removed top shel glass above crisper--removed old rail by lifting up--and place new one in slots provided---simple!! Part was delivered in less than 3 days-------very fast and cheap !!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from NEWTON, NJ
- Parts Used:
- W10619951
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fridge was leaking water because of bad drain
Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues
Fixed the problem
Have had no more drain issues
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from ATLANTIC BCH, FL
- Parts Used:
- W10443315
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Freezer Compartment Gasket Replacement
My freezer compartment gasket was torn and needed replacement. This was on a bottom freezer Kenmore refrigerator. I couldn't find directions for how to take the freezer compartment door off, and figuring out how was the hardest part. Here are the instructions:
1. At least 24 hours prior to starting, remove the gasket from the packaging and lay it out in a warm area, to allow the creases to come out.
2. Unplug the refrigerator.
3. You will have to take BOTH doors off, so put at least the freezer compartment contents in a cooler so they don't thaw. Also remove all items from the refrigerator and freezer door.
4. Remove the refrigerator door first - remove the plastic cover from the top hinge, then remove the 3 metal screws holding the hinge in place. Lift the door up, and it will come right off. Set it aside.
5. Now remove the freezer door - there is one bolt head, for the top hinge pin. Remove it, and lift the door up and put it down on a table.
6. Towards the center, pull up on the old gasket, and use a pair of diagonal cutters to cut it in half. It will take a few cuts, but eventually you will get it out and cut in half. Then remove the old gasket.
7. The new gasket simply presses in. Start at two diagonal corners, then press the other two corners in, then do the straight sections.
8. Now replace the freezer door, then the refrigerator door, plug in the refrigerator, and put the contents back in.
1. At least 24 hours prior to starting, remove the gasket from the packaging and lay it out in a warm area, to allow the creases to come out.
2. Unplug the refrigerator.
3. You will have to take BOTH doors off, so put at least the freezer compartment contents in a cooler so they don't thaw. Also remove all items from the refrigerator and freezer door.
4. Remove the refrigerator door first - remove the plastic cover from the top hinge, then remove the 3 metal screws holding the hinge in place. Lift the door up, and it will come right off. Set it aside.
5. Now remove the freezer door - there is one bolt head, for the top hinge pin. Remove it, and lift the door up and put it down on a table.
6. Towards the center, pull up on the old gasket, and use a pair of diagonal cutters to cut it in half. It will take a few cuts, but eventually you will get it out and cut in half. Then remove the old gasket.
7. The new gasket simply presses in. Start at two diagonal corners, then press the other two corners in, then do the straight sections.
8. Now replace the freezer door, then the refrigerator door, plug in the refrigerator, and put the contents back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sharon from RACINE, WI
- Parts Used:
- W10830189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Original door gasket was cracked and torn
Replacement gasket extremely easy to install. Used hair dryer to soften and straighten out “kinks” in replacement gasket. Pulled old gasket out of groove in refrigerator door. Lined up corners of new gasket and pressed into place with my fingers. Went in exactly as video showed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Judy from BALD KNOB, AR
- Parts Used:
- W10830189
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The rubber liner around the refrigerator door was splitting and cracking
I watched the video and it took away my trepidation. I did what it said and it went right in!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sung-Su from BISMARCK, ND
- Parts Used:
- W11396033
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broke the Rocker Switch in Fridge side
Popped out with butter knife and unplugged 3 prong connector and reversed with anew switch.
But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.
Maytag should recall that Rocker Switch and build with better materials.
But, unfortunately it got broken again exactly same way as before.
So, I ordered same switch again for 2nd time.
Maytag should recall that Rocker Switch and build with better materials.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Galen from WASECA, MN
- Parts Used:
- WPW10196393
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fresh Food Compartment occasionally going down to 28-30 degrees F
Failure detected as Damper Control at upper rear of compartment would continuously open/close, would never stay open or closed. Sometimes the main board would turn it off (maybe a low thermistor limit?), but it would stick open a bit, and keeping letting freezer air into fridge. Could have potentially been control board, but as it turns out after disassembly of the defective damper, the internal microswitch was stuck in the closed position so it wouldn't shut off the motor. Easy fix by gently pulling the cover off the damper control, pull out Styrofoam encasement, then a phillips to remove the damper assembly. Gently push tabs to release wire connectors. Reverse the process and you're done! If I really wanted to go on the cheap, I could have just changed the microswitch, but that looked like a shaky maneuver at best. This site saved me on this one, so happy to share my experience with this Maytag and its nasty habit of freezing my milk and eggs!! :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Blairsville, GA
- Parts Used:
- WPW10284685, WPW10284684
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Parts ordered on Sun Arrived Tues (local stores closed)
Talking with the service tech and youtube video it was a snap... Saved a service repair and a 25% parts mark up..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Keith from GRANTS PASS, OR
- Parts Used:
- W10830189
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Bad gasket
Pulled off old gasket
Put new gasket in the groove
Gasket fit perfectly
Thank you
Put new gasket in the groove
Gasket fit perfectly
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Allan from Tucson, AZ
- Parts Used:
- WPW10671238
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken center crisper rail
Total time 10 minutes. 9 minutes to clear out the food and 1 minute to install the part. Installation was self evident and could have been done blindfolded. Part just snapped in.
Was this instruction helpful to you?
Thank you for voting!