6GD25DCXHS14 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from Cutler Bay, FL
- Parts Used:
- WPW10321304, WP2180224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice guide broke off; bin cracked
We saved hundreds in not calling the service. The ice guide popped right in. As one other person mentioned, took a little force, but no problem. And bin slid in easily. DIY is the way to go these days.
Thanks, PartSelect.com
Thanks, PartSelect.com
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Fresno, CA
- Parts Used:
- WP2182179, WPW10329686
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Refrigerator door wouldn't self-close
Super-easy... First, empty refrigerator door. Then, just remove the bolt that goes through the cover over the top hinge. This exposes three more small bolts. Remove these and the top hinge assembly will lift off. Lift door off. Remove cam from door and lower hinge, slip new cams on, and reassemble. The hardest part was pulling all of the junk stuff out of the refrigerator door. Who know you could accumulate so much salad dressing?
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Casper, WY
- Parts Used:
- WPW10312300, W11342242
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I was just missing two parts to the icemaker
I slid in the arm and slid in the ice bucket with augar.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Fort Collins, CO
- Parts Used:
- WP2182179, WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Refrigerator door of our double door not closing
Removed the top bracket (3 5/16 size hexhead bolts)
Lifted door free of the bottom cam and hinge socket
(after, of course removing the items from the door shelves!)
removed one bolt holding the lower came to the cabinet.
Pried the cam loose, replaced with new and re-bolted
removed one bolt from cam on door - unable to remove cam until I removed the guard bracket (two more bolts)
worked the plastic cam from the door by twisting it and pulling the socket from it's hole.
Slipped the new cam into the socket hole, aligned the bolt hole and bolted it tight.
Aligned the top cam to the bottom cam as I replaced the door. Re-attached the top bracket.
All bolts were 5/16
Door now works perfectly again.
Lifted door free of the bottom cam and hinge socket
(after, of course removing the items from the door shelves!)
removed one bolt holding the lower came to the cabinet.
Pried the cam loose, replaced with new and re-bolted
removed one bolt from cam on door - unable to remove cam until I removed the guard bracket (two more bolts)
worked the plastic cam from the door by twisting it and pulling the socket from it's hole.
Slipped the new cam into the socket hole, aligned the bolt hole and bolted it tight.
Aligned the top cam to the bottom cam as I replaced the door. Re-attached the top bracket.
All bolts were 5/16
Door now works perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tony from Lake Forest Park, WA
- Parts Used:
- W10823377
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
The door shoot plastic had cracked allowing air to get into the freezer compartment.
I unplugged the fridge, removed the face plate on the front, disconnected the power feeds, unscrewed the electrical panel and moved it out of the way.
I then dismantled and removed the broken part and installed the new part. I was able to use the rest of the existing parts to get the job done.
I put everything back together, and voila! it works great.
I then dismantled and removed the broken part and installed the new part. I was able to use the rest of the existing parts to get the job done.
I put everything back together, and voila! it works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Betty J from Amherst, VA
- Parts Used:
- W10823377
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Ice cube door would not close pr0perly
Because of the design change of the door hinge it was more difficult to slide the pin into the door and spring. I used an allen wrench to hold it in place on the left side so I could slide the pin in the right hole. Then removed the allen wrench so I could slide the pin all the way. I was very impressed with the time that it took to get the kit. I ordered it about 1:30PM and the following day I had the kit delivered by 6PM. FANTASTIC SERVICE!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- dean from los angeles, CA
- Parts Used:
- W10508993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broker cover to crisper
the piece fit perfectly and delivery was within a couple days. very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gabriele from HERNDON, VA
- Parts Used:
- WPW10321304
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Replaced cracked door bin
Easy, peasey. I popped the old one out and put the new one in. Less than 30 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- María from BELLEVUE, NE
- Parts Used:
- WP2156022
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken shell
Pot the part on
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lila from PEMBROKE PNES, FL
- Parts Used:
- W11497323
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
old bin was broken, plastic chipped off various places, needed replacement
Fit in perfectly. Slid out the old one, replaced with the new one. Very easy. Very satisfied with the transaction.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nola from Yacolt, WA
- Parts Used:
- WP2156022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The bottom shelf front had cracked and finally broke, sending food containers to the floor when door was opened.
It took just a few seconds to snap the shelf into place. Thank you for sending the part so quickly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from JONESBORO, AR
- Parts Used:
- WPW10312300
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Auger broke
Took old one out replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Jacksonville, FL
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Ice would not dispense from the door
Removed ice bucket and discovered the auger drum was broken.
After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.
Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.
Works great now, crushed and cubed ice dispenses thru the door like new.
After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.
Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.
Works great now, crushed and cubed ice dispenses thru the door like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ken from Cedar CVity, UT
- Parts Used:
- 4388736
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Ice would not come out of the despensor
Pulled out the ice bin and dumpted ice in the sink. Use 1/4 inch nut driver to take out all 1/2 inch screws. Be careful to watch how door spring and holder goes. Pull assembly apart and remove alger. Plastic nut on end of alger has reverse threads, remove it and then remove broken alger drum. Replace with new drum and reassemble in reverse order.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harry from COLUMBIA STA, OH
- Parts Used:
- WP2149705
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Lights not working some times
Removed old switch and installed new - but did not solve problem
Was this instruction helpful to you?
Thank you for voting!