3ET18ZKXAN01 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Clips that held the door bar on the interior of the door were broken off
Ordered new replacement parts. Took new parts to the work site and proceeded to install them. First removing the reminance of the old clips from the bar its self. Using a flat screw driver pri the metal tabs open so the old part can be removed. Reset the crimp in the metal bar and install the new clip into the ends of the metal bar. Insert the new clips into the appropiate holes in the door liner and pop into place. Very easy repair when you have the right parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Virginia Beach, VA
- Parts Used:
- WP2155013
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Kick Plate Clip Broke
On the left side I unscrewed the screw and replace it with a new one . The right side in had to take s file and file of the rivet. You can use a rivet gun or a metal screw to replaced the clip. Once it is finish open the refrigerator door to see how to line the kick plate into the clip. A piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Douglas from Pahrump, NV
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers
Water fill tube was broke at the 90° in back of the frige
Water was already off. All I had to do was pull the fridge away from the wall, remove two screws that hold the fill tube onto the back of the frige, then remove the fill tube. Install the new fill tube, reinstall the two screws. Had to cut the water line straight and clean, slip on the new Compression nut and farrell and insert into the new fill tube, tighten-up, good-to-go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from Crestline, CA
- Parts Used:
- 1123394
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
not cooling
R/R part, 3 screws reconnect 3 wires. easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jill from Ivanhoe, MN
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
water tube froze and got bent so it would not fill ice maker properly
Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janet from Denver, PA
- Parts Used:
- WP4387503
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
refridge. was not defrosting.
took shelf off of freezer, took ice cube maker out, took back panel off changed defrost thermostat.then re-assembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- judi from wallowa, OR
- Parts Used:
- WP2196157
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker not making ice
repair went well. Ice maker still not making ice. UGH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Bloomington, IN
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken water line connection
Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- R. from Weaverville, CA
- Parts Used:
- 4386917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door shelf end bracket
Simple. snap together instalation, no tools required. Thank you partselect for having the parts pictured with a size grid in the background, without that size grid, it would have been more difficult to select the right part. And, may I add, "my local appliance repair person indicated- he could not locate a repair part." I found the part via google search, and partselect.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shirley from wind gap, PA
- Parts Used:
- WP2196157
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
icemaker not working
I followed vidio instructions, took about 15 minutes. Fridge making great ice cubes again. Felt prouud of the repair I did being 70 years old and a female. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elizabeth L from Beaver, WA
- Parts Used:
- 4386917
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
End caps broke leaving shelf unusable
Snapped in new end caps and attahed existing shelf bar. Have done this twice. We tend to stuff too many items on that bottom shelf.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lucy Ann from Virginia Beach, VA
- Parts Used:
- WP2172748
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Crisper support missing
Cut support and replaced. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Coral Springs, FL
- Parts Used:
- WP4387503
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Freezer would frost up then frig temp would rise to un safe tempertures
UN plugged refrigerator,waited 24 hours to let defrost,removed panels,cut out old Bi metal Defrost thermostat,wired in new thermostat,reassembled freezer,plug back in,working great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Margo from Baraboo, WI
- Parts Used:
- W11581579
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf support in freezer
Removed correct part from those provided and slipped it into position. No tools necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lee from Brooklyn, NY
- Parts Used:
- 4387478
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Protective cover for bulb had melted
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.
Was this instruction helpful to you?
Thank you for voting!