WSF26D3EXT00 Whirlpool Refrigerator - Instructions

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Removed ice bucket and discovered the auger drum was broken.

After I received the new part, I removed the front screws of the ice bucket, removed the clip that held the auger and other parts together, and then slide each part off the auger until I got to the broken drum.

Assembly was in reverse except you must pay attention where all the spacers and ice crusher bars go back into the original position. This was the most difficult step.

Works great now, crushed and cubed ice dispenses thru the door like new.

Pulled out the ice bin and dumpted ice in the sink. Use 1/4 inch nut driver to take out all 1/2 inch screws. Be careful to watch how door spring and holder goes. Pull assembly apart and remove alger. Plastic nut on end of alger has reverse threads, remove it and then remove broken alger drum. Replace with new drum and reassemble in reverse order.

The do it yourself video that was attached was great

ordered new filter, removed old filter from fridge, and installed new one

1. Pull out drawer. 2. Remove screws to release the auger. 3. Unscrew the end of the auger. 4. Pull parts off. 5. Replace drum. 6. Replace parts in the correct order. 7. Twist end of auger back on. 8. Replace unit onto drawer and install mounting screws. 9. Place drawer in freezer. 10. Test ice dispenser. 11. Watch kitten run to refrigerator and beg for ice cube. 12. See smiles on family members faces.

1. Removed 2 screws on top hing.
2. Easily lifted door and place on table.
3. Removed set screw for door cam.
4. Removed stop bracket.
5. Reversed steps 4 thru 1.

When tightening top 2 screws, make sure door gap is consistent and top of frig door aligns with the top of the freezer door.

NOTE: The lady at PartSelect who helped me with my order was great. Took the time to verify my parts. Prior to this I had bought the part from a nearby appliance parts store. They sold me the wrong part, even though I showed them a picture of my model number plate b4 ordering. In the future, I will always go to PartSelect for my appliance part purchases.

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Removed all ice from bin and let it thaw. Removed all screws and nuts from the front to release the ice crusher and the long bit. Had already printed out all the advice from others on the on-line section about taking photos and not getting the crusher blades out of order. Removed the clip with needle nose pliers and the washer. Removed the blades laying them down in exact order and direction they came off. Put on the new auger drum and reversed everything. It was nice to know that the plastic screw that held the clip is a reverse thread, otherwise we might have broken the dang thing. Too bad there aren't instructions with the part when you get it instead of just a diagram. All-in-all, it went well.

I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me.
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.

Unhooked water line from house to fridge then unbolted valve from fridge body then removed plastic water line from fridge to valve by pushing in on pex release tab then reversed process with new valve. Works like a charm. No more leakage. Wood floor is dry and Happy!

Unplug, then on the freezer side, remove the drawers, then remove the screws holding the sheet metal cover, remove the rails (for the drawer) that interfere with removing the sheet metal cover. pull the wires off the motor. There is a big plastic piece that holds a small plastic piece that holds the motor. Remove the plastic piece that holds the motor/fan (you might be able to swap the motor by removing the little plastic piece that holds the motor, or you can remove the bigger piece and then remove the small piece that holds the motor). Pull the fan blade off (to reuse), swap the motor. NOTE - the new motor wire terminals may be on the opposite side of the motor vs. the old motor - that is not a problem - there is plenty of room for the wires. After the motor is installed put the fan blade back on, reinstall the removed plastic pieces in the back of the refrigerator. Now, I'd suggest a quick test. Make sure the new motor works and the fan blows before you button it up. Once you know it works, power it off, and put the sheet metal cover back on, reinstall the basket brackets, put the baskets back in place, close the door, and turn it back on.

Unplugged freezer turned off water removed 3 nut screws Unplugged old ice maker installed new ice maker