WRT1L1TZYW00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from Roanoke, VA
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door light socket was broken and hanging down
The refrigerator light in our Kenmore fridge has been flaky for a number of years. The slightest bump would knock it out of the hole it fits into leaving the bulb dangling. Usually since we were used to it, we could avoid bumping it so it was no real problem, but a recent visitor bumped it and it once again was hanging. I decided this time, to take a serious look at it and fix the problem for real. I had options, duct tape, hot glue gun, goop...or a new part! A quick search on the internet, and I found www.PartSelect.com I entered my model # , quickly found the correct part number. The part came 1 1/2 days after I ordered it. The repair was very simple, I unplugged the fridge, removed the wires from the spade connectors on the old light socket, and attached them to the new socket. I then pushed the socket into the hole, and with new spring clips, it snapped snuggly into place. The socket came with extra wire connectors which I didn't need, the socket fits multiple brands of appliances. It also came with a bulb protector, but that wasn't needed for my fridge either. I was very pleased with the speed and ease of the repair. No more dangling light bulbs!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Hans from OGDEN, UT
- Parts Used:
- WPW10475495
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Raise side of fridge and slide 2x4 under side with broken wheel.
Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Manchester Center, VT
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Refrigerator light would not stay on
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
reassembled the pieces.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from PARADISE, TX
- Parts Used:
- WPW10468556, WPW10468555
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken tracks on the Meat/Cheese drawer.
The broken tracks popped off with a little effort, and the new tracks snapped in place. No tools required, except a screw driver helped to pop the broken tracks out, and snap the new ones in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from Annapolis, MD
- Parts Used:
- 4388947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I broke the plastic handle on my brand new refrigerator
Removed the two screws on top, then slide the trim cover at the bottom of the handle down and removed the third screw to remove the handle.
New handle goes in with two top screws first, then third screw at tem bottom of the handle. Don't forget to slide the trim piece back on to cover the third screw...
New handle goes in with two top screws first, then third screw at tem bottom of the handle. Don't forget to slide the trim piece back on to cover the third screw...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from LEWISBURG, KY
- Parts Used:
- WPW10392132
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer cold, refrigerator warm
Simply cut wires from old bi metal and joined to new part with wire nuts. Simple repair, but it did not correct the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from WEST CHESTER, OH
- Parts Used:
- W11700559
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
I added an ice maker to a 20 year old refridgerator
I added an icemaker kit. Everything I needed was in the kit. The refrigerator was presetup for an icemaker it was just never added. The only problem I had was that the holes for attaching the water solenoid were not pre drilled so I had to drill them myself and use sheet metal screws. The icemaker is working great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from POWELL, OH
- Parts Used:
- W11700559
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Getting Ice Maker to sit in place prior to tightening screws.
Don not completely remove holding icemaker screws. Unit slips over screws and drops down into place and the use nutdriver to tighten in place. Rest of unit was sound and wasn’t replaced.
After icemaker is installed wait for a while and unit self activated and creates ice cubes.
After icemaker is installed wait for a while and unit self activated and creates ice cubes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Winston A from Brooklyn, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Raplaced switch
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert G from AIKEN, SC
- Parts Used:
- WPW10279909
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Ice maker not working. Motor working, not getting water to icemaker.
Replaced inlet valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from MACOMB, OK
- Parts Used:
- W11700559
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
It was my first time to install a ice maker.
I first read the instruction manual then I watched the installation video. My water line to it was 3/8. Went to the local ACE Hardware to purchase a short peace of 1/4 copper tubing and the fittings to connect them together. It makes ice every 55 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Houston, TX
- Parts Used:
- WP2195947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Refrigerator Trim was Bent
Ordered the new part, it was the perfect size and slipped right on to the existing brackets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TROY, IL
- Parts Used:
- WP2315539
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Fan motor died
First, made sure new fan worked then Placed back in bracket with bushings-only goes in one way, pushed fan back on. screwed bracket to back of freezer and ran the wires to their original place, plugged in the two plugs, put the back piece up attaching ground and pulling ice maker plug thru, screwed back on. Plugged in ice maker, mounted ice maker on freezer wall. Plugged it in. Exact reversal of how it was removed. Not a lot parts to get confused.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from HOUMA, LA
- Parts Used:
- W11700559
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Installed a Ice Maker
Very easy to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Albuquerque, NM
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
lights wouldn't come on/work in refrigerator
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!
Was this instruction helpful to you?
Thank you for voting!