WRT1L1TZYB00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from LANSDALE, PA
- Parts Used:
- WPW10584888
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ref not holding temp
Remove 4 -1-4 screws with nut drivers assembly drops down tstat pups out remove wires replace tstat n put back in reverse !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pamela from PARADISE, TX
- Parts Used:
- WPW10468556, WPW10468555
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken tracks on the Meat/Cheese drawer.
The broken tracks popped off with a little effort, and the new tracks snapped in place. No tools required, except a screw driver helped to pop the broken tracks out, and snap the new ones in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dave from Manchester Center, VT
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Refrigerator light would not stay on
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
reassembled the pieces.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Byron Center, MI
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light in my refrigerator didn't work.
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved me $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Elmer from Annapolis, MD
- Parts Used:
- 4388947
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
I broke the plastic handle on my brand new refrigerator
Removed the two screws on top, then slide the trim cover at the bottom of the handle down and removed the third screw to remove the handle.
New handle goes in with two top screws first, then third screw at tem bottom of the handle. Don't forget to slide the trim piece back on to cover the third screw...
New handle goes in with two top screws first, then third screw at tem bottom of the handle. Don't forget to slide the trim piece back on to cover the third screw...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Suzanne from STERLING HTS, MI
- Parts Used:
- 4387478
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Refrigerator light would not turn on.
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from LEWISBURG, KY
- Parts Used:
- WPW10392132
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Freezer cold, refrigerator warm
Simply cut wires from old bi metal and joined to new part with wire nuts. Simple repair, but it did not correct the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from WEST CHESTER, OH
- Parts Used:
- W11700559
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set
I added an ice maker to a 20 year old refridgerator
I added an icemaker kit. Everything I needed was in the kit. The refrigerator was presetup for an icemaker it was just never added. The only problem I had was that the holes for attaching the water solenoid were not pre drilled so I had to drill them myself and use sheet metal screws. The icemaker is working great.
Was this instruction helpful to you?
Thank you for voting!
too much frost in freezer
pulled out gasket and then had to put new gasket in place. Took door off laid it on the kitchen table. Used the small rounded end scissors so that the gasket would get perforated.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from MACOMB, OK
- Parts Used:
- W11700559
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable), Wrench set
It was my first time to install a ice maker.
I first read the instruction manual then I watched the installation video. My water line to it was 3/8. Went to the local ACE Hardware to purchase a short peace of 1/4 copper tubing and the fittings to connect them together. It makes ice every 55 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darcie from VINELAND, NJ
- Parts Used:
- 2159061
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
freezing everything
Removed old gasket. Wiped everything down. Popped in new gasket.
It was a little tedious, but it went in easy enough. Some reviews said the new gasket was kinked and bent. Mine I am happy to say was smooth. Some things are still getting quite cold like vegetables and ginger ale.(almost freezing). But it is way better than it was. Saved us from having to purchase another refrigerator. The fellow who helped me made it easy to order and everything went smoothly. I appreciate the help and patience you provided.
I
It was a little tedious, but it went in easy enough. Some reviews said the new gasket was kinked and bent. Mine I am happy to say was smooth. Some things are still getting quite cold like vegetables and ginger ale.(almost freezing). But it is way better than it was. Saved us from having to purchase another refrigerator. The fellow who helped me made it easy to order and everything went smoothly. I appreciate the help and patience you provided.
I
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from NIAGARA FALLS, NY
- Parts Used:
- 2159061
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
gasket was cut and ripped
rippped the old one off and carfully put the new one on with a flat head screwdriver at an angle as not to rip the new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from HOUMA, LA
- Parts Used:
- W11700559
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Installed a Ice Maker
Very easy to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from TROY, IL
- Parts Used:
- WP2315539
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Fan motor died
First, made sure new fan worked then Placed back in bracket with bushings-only goes in one way, pushed fan back on. screwed bracket to back of freezer and ran the wires to their original place, plugged in the two plugs, put the back piece up attaching ground and pulling ice maker plug thru, screwed back on. Plugged in ice maker, mounted ice maker on freezer wall. Plugged it in. Exact reversal of how it was removed. Not a lot parts to get confused.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from POWELL, OH
- Parts Used:
- W11700559
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Getting Ice Maker to sit in place prior to tightening screws.
Don not completely remove holding icemaker screws. Unit slips over screws and drops down into place and the use nutdriver to tighten in place. Rest of unit was sound and wasn’t replaced.
After icemaker is installed wait for a while and unit self activated and creates ice cubes.
After icemaker is installed wait for a while and unit self activated and creates ice cubes.
Was this instruction helpful to you?
Thank you for voting!