NWT0002D01 Whirlpool Refrigerator - Instructions

I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.

Freezer worked great, refrigerator stopped getting cold and lots of ice formed around the condenser on the bottom of the refrigerator.
First I had a serious ice issue, ice build up around the bottom of the refrigerator and all through the cold air vents, condenser and cooling fan. I unplugged of the fridg and let defrost over night. I also took all the cold air vents out and cleaned them.
Then I followed the switch install video very simple switch install. Now the Refrigerator works Great nice and cold.

Ordered the leveling bolts, very fast shipping, parts correct as shown. Purchased a condo by the shore, frige had no levelers, they went in smoothly & was done in no time.
Steve

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

The drawer slid right into the refrigerator. No installation was needed. The part arrived quickly. No problems at all. I wish I would have ordered this part sooner!

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

ordered the parts ,defrost timer and bi-metal thermostat,assumed it would be more practical to replace both than take a chance . watched a video on how to disassemble the control panel and remove the the timer and the back panel of freezer for the bi-metal thermostat,very clear instructions provided .took about 25 minutes to replace both parts and now is working properly again,,Thanks Again PartSelect for the fast service and delivery

Followed the video instructions.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Toddler left the fridge door open for an undocumented amount of time. The freezer was operating perfectly but the refrigerator was not cooling. After some research I ordered the part needed and went to work. Process was simple, just keep track of the fans mounting bracket. I installed it upside down and the holes didn't align with the back wall freezer cover.

Step 1: Unplug the fridge
Step 2: Gloves and safety goggles
Step 3: Tools - Socket Set and screw drivers. Hammer and chisel for the ice build up.
Step 4: Remove the back wall of the freezer carefully
Step 5: Remove fan and motor housing, unplug Hot, Neutral and ground wire from motor
Step 6: Drink a beverage
Step 7: Remove fan and motor from housing. You will have to reuse the rubber gaskets/washers so do not dispose.
Step 8: Install new motor and connect the hot, neutral and ground. Do not overtighten the screws connecting the motor housing to the mounting bracket.
Step 9: Before mounting the bracket, plug in the fridge to confirm the fan is operating.
Step 10: Put everything back and have another beverage.

Piece of cake. It took me longer to remove the food from the freezer, remove shelves and back panel than to do the repair. I heard the fan making some noises so I replaced both the fan and defrost thermostat. I used the instructions submitted by a another customer. My 20+ year old fridge is like new now.

I replaced the defrost relay folling instructions I read on the internet--and it still didn't work--So I replaced the compressor start relay which was easier than the defrost relay--it worked and the fridg is working good.