GSF26C5EXS03 Whirlpool Refrigerator - Instructions

Take out shelves and back shelf pins and remove long cover. Disconnect wires and take old part out and installed new part. Then reversed and put everything back together. It worked perfect. No more noise

Great

Myself
Perfect fit
Quick shipping
Excellent service!!

I took the cover off, and noticed the tabs holding the timer wheel were broken off on one side. after removing the wheel, I noticed the shaft from the ice lifters was broken. Since the only way I could repair it was to buy the entire module, which I did. I received my part in 3 days. When it came, I began removing the old module by taking out the three screws holding it. After replacing the module which took about 10 minutes, my machine was making ice within about an hour. My ice holder was full in 3 days. Albert Moran, Milton, Fl

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.

Just follow youtube examples. Work in freezer. Troubles was I didn't fix the problem. Experts say thermostat is the best one to replace (53%). Anyway they are not always right.

Remove the ice bucket and check that the auger that turns in the ice bucket is free to turn. Cover the open freezer with cardboard or whatever to retain most of the freezer temperature. Remove the holder that supports the top of the motor shaft. Check the splines on the upper part of the motor shaft and also check the seal under the holder. Open the access the door to the motor, remove wiring connector and unbolt the motor. Check the lower splines on motor shaft for condition, clean the shaft and apply new grease to the splines. Before installing, connect the wiring to the new motor, push the door switch in, press the ice dispenser arm outside the door to make sure the motor runs. If all ok, check the motor shaft for fit in the new motor. Be careful not to install the motor shaft too deep in the motor splines, otherwise there may not be enough spline showing on the top end to engage the auger. Bolt the motor in place, close access door and install the holder and ice bucket and make sure everything works. If there is not enough spline showing thru the holder to engage the auger, take pliers and pull the shaft up a bit. This seems to be a hit or miss fit on the shaft but you can adjust the height of the shaft without taking every thing apart again. That's all, not difficult at all. But do check parts and pieces for anything else you might need, parts wise, before ordering the motor by itself like I did. Shipping is high, so try to order any associated parts needed when you order the motor. By the way, This site are great to work with!

I use a Screw drive a Nutdriver set Needlenose Pliers and it took 30mins to fix.

Unplug fridge, remove shelves, remove back cover, unplug old motor, remove adapters from old motor, put adapters on new motor, install new motor, replace cover, replace shelves, plug fridge back in, give it 24 hours to stabilize thermally.

with vidio

Opening up the Evaporator Fan section was a quick and easy job. After opening, I checked and removed the fan and looked at the grommet. The grommet on the fan was tight and secure and I could no longer hear the noise. I closed the opening. Something I had done while checking the fan grommet must have solved the problem. I have not hear the noise again!

Removed 4 bottom screws. Removed module screws. Replaced module and motor with new parts (came assembled). Replaced module screws and installed the ice maker with the 4 bottom screws.

1) Turn off the power to the refrigerator 2) Remove the top shelf and ice maker door 3)Remove three hex screws holding the ice maker in place, 4) Unplug the electrical cables and remove the ice maker 5) Remove the plastic cover to the motor module 6) Remove three screws from the motor module and seperate from the housing 7) Remove two mounting screws for the motor module 8) Seperate the motor module from the ice tray 9) Remove and replace the plastic ice stripper and rake10) Reassemble in reverse order. Note: Be patient after re-installing the ice maker. It might take an hour or two before its cold enough to kick back on and make ice.

Removed old filter then insert new filter and pushed door closed