GX2SHDXVB00 Whirlpool Refrigerator - Instructions

After lots of internet exploring and diagnosis, the icemaker comes right out, and with three screws out and in, the job is all but done. Don't pay anyone for this repair!!!!!

The ice mold has a coating on it. Over time the coating deteriorates. If your ice maker leaks water into the ice reservoir inspect the mold to see if the coating is compromised. If so, replace with new.

Remove the ice maker assembly. 3 small hex screws. Unplug power cord. Disassemble ice maker assembly. Remove ice mold/heater. Replace with new. Reassemble.

Pulled out on gasket seal at top right corner of door and when loose pealed the seal out around door. Installed gasket by inserting channel insert into door groove and pressed gasket in while lightly pulling down to stretch seal out to facilitate inserting gasket lip into door channel. Bada bing! Done. Good fit. Note: I laid out gasket in the sun to soften it up as there were some small wrinkles in material from being folded for shipping. Hair dryer would work too!

i had used your web site before and i read several problems that your readers had. i went to the back of the unit, removed the bottom cover and right there the i found the run capacitor and i chaged it. since i had only ordered this part to save money i went back and ordered the Start Device which when i took it off it was completely burned. the replacement part came labeled with 2 different compressor #, so i picked the one that i had and unpluged each wire. the part may differ from the one that it's in the unit but it worked when i pluged everything back on. it also helps to take a picture of everything before removing the wires in case you have to leave it and come back later. i hope to use this refrigerator another 10 years. thank you all for your help.

Removed the middle screw and the whole rail came of. Unplugged wires and removed old rail. Plugged in the new rail and slid top and bottom slides on and put on the middle screw. Job finished

replaced the poorly designed "duck bill" drain with this P trap. Very simple repair done by accessing through the back of the refrigerator. The video on this website walked me right through the repair. It did however fail to mention that the ice has to be removed from the inside. I had to remove the drawer face and pull outs. Then the ice maker and back panel are removed. I used a heat gun and screwdriver to chip and melt the ice build up. If one had the luxury of having another refrigerator to move food in to you could just unplug the unit until the ice melts.

Repair was a piece of cake. My only wish would have been a little more informed on a few other parts I could have replaced as well. It obviously would have increased my cost, but would have simplified the install process, and still would have been cheaper then calling a service guide. I would recommend buying and installing the new gaskets when doing this. And possibly the steel support bar that goes threw the plastic shelf. Removing that bar was the most difficult task, difficult only that if you used to much force, SNAP!! and then your pissed! and have to start all over.

Remove the existing mullion rail:

- Remove the screw from the center hinged cover.
- Remove the mullion rail by pushing upward. The top and bottom hinges slide over tabs attached to the door. I had to bump it gently from underneath.
- Disconnect the three wire connector that's underneath the center hinged cover.

Install the new mullion rail by reversing the above steps:
- Connect the three wire connector and snap it into its holder.
- Slide the new part over the top and bottom hinges. Be sure that all three hinges are correctly lined up before sliding the rail over the tabs.
- Push it down far enough that the hole for the screw in the center cover is lined up with its corresponding receptacle in the door.
- Replace the screw.

I searched the internet for the correct part and reviewed the instructions on the internet. Upon ordering the correct part I was provided a link to a video that walked me through step by step. The very first thing I did was unplug the refrigerator.I then located the control board located in the housing in the ceiling of the refrigerator. Using a screwdriver I was able to carefully separate the housing from the refrigerator ceiling . Unplugged the housing and then had to separate the plastic housing to locate the control board. Ran into a little difficulty at first separating the plastic tabs but with a screwdriver carefully pried the tabs. Once completely open is where the control board was. More plastic tabs holding the control board in place. Carefully separated the board from the tabs. The were two plugs that needed to be separated from the board. Used a screwdriver to get the plugs separated.The new board you had to bend carefully at a joint so the board became two pieces. Snapped the boards in place. Plugged the board in two spots. Put the housing together and put the housing in place in the refrigerator. Plugged the refrigerator in. All lights came on and then had to program the board. The instructions were spit on. The code is located inside the fridge were the model tag is. Programmed correctly. Word of advice read the directions a few times you can't go wrong. So far it's day 7 after I installed the board and no ice building up. According to the internet the control board controls the defrost function on my model. Very happy. I'm still watching the freezer but I'm pretty sure I fixed my matter. Thanks for sending the right part and the video. Repair went well. Just take your time and go easy because everything involved is plastic. I didn't want to break any tabs I had to deal with.

I pulled off the old gasket and placed the new gasket in the existing groove, shut the door; problem solved!

turn off water and unplug fridge. remove ice maker bottom mounting screw. just loosen the 2 top mounting screws. unplug wire harness from back of fridge. remove old icemaker from freezer compartment. once removed, salvage square endcover and reinstall on new maker. unfasten wire harness from old maker and reinsatll on new one. reinsert thermal wire in new ice maker holding bracket. remove second wiring bracket and reinstall on new maker to hold remaining wires (not mentioned on "how to-" video). remove old ice maker on/off bale and reinstall on new one. remount new maker to top mounting screws, reinsert harness plug into fridge. replace bottom screw,

Unplug ref then remove lower(freezer) panel plus trays and thermistor’s cover/holder then remove the evaps cover. I found the evaps all frozen up. Cut and remove old thermistor, strip wires 1/2 inch then cut the new thermistor wires to length and strip 1/2 inch, use the enclosed insulated crimp type connector and put back everything in the reverse order. It works great afterwards.

The lining of the ice mold (Whirlpool) started flecking off (black flecks in the ice cubes), so I decided to replace the mold.
Loosen the two 1/4 inch upper nuts and remove the lower nut to remove the ice maker from the freezer. The hardest part was getting it unplugged. I used a small blade screwdriver to release the catch on the connector and pull it out.
Remove the ice maker front cover. If you have a skinny enough phillips screw driver, there are two deep set screws through two holes on the lower portion of the control module (otherwise, remove the three screws on the controller, unlatch the shut-off arm from the control module, and separate the controller to access the mold screws). Unhook the shut-off wire from the end of the tray. Unscrew the two screws holding the mold and remove the mold.
Remove the plastic hardware from the old mold and install on the new mold.
Attach the new mold on to the control module.
WARNING WARNING WARNING!!! The mold I bought already had the alumilastic on it for the contact point to the thermostat. When I installed it and tightened the screws, the alumilastic was dried out, didn't squash down, and dented the bi-metal thermostat on the controller, ruining it. I had to buy a new thermostat. Be sure to check that the alumilastic is pliable. If not, take it off and buy some fresh to put on there.
Re-install the ice maker. It took a while to get the first batch of ice because the ice maker was at room temperature and I had the freezer door open for several minutes. So the freezer had to get cold and the ice maker had to chill down. Once everything got cold, it started making ice again.

(1) Slide out appliance and remove power source. (2) Removed lower access cover on rear of refrigerator. (3) Disconnected plug to the condenser fan motor. (4) remove blades by pulling gently forward (5) remove mounting hardware holding the fan motor (3 screws) (6) motor is now free and new motor can be installed

I ordered a right & left gasket but when they arrived there was no indication of which was the right or left one...so I just had to guess...I easily lifted the old gasket away from the door & removed. Then starting at the top began inserting the portion that goes into the groove with the help of the table knife, continuing down both sides..then sat on a stool to push the bottom section into place...Had to go back over several areas to reseat but finally closed the door to hopefully set the gasket..Drank some hot tea, then removed the left gasket & began the process all over...The extra flaps ended up on the left side of the door so I may have to remove this side and reposition...I'll check it in a few..then will blow all with a warm setting of the low dryer to continue helping the molding process..