KTLA22EMSS03 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Michael from Santa Clarita, CA
- Parts Used:
- W10190935
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice maker made no ice
After taking apart the ice maker, the only obvious replacement was the motor assembly. I check various Internet sites and found the best price at PartSelect.
I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.
After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.
Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!
Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.
I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.
After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.
Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!
Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barry from Lowell, NC
- Parts Used:
- WP2186494B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Filter Cap Broken
Replaced the cap no tools needed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Long Valley, NJ
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Ice Maker didn't produce ice cubes.
It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from West Bloomfield, MI
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
icemaker was overfolwing with water
ordered the part, pulled out the icemaker unit, removed the module, put the new module in, reinstalled the ice maker unit and let it run.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chyllene from OXON HILL, MD
- Parts Used:
- WP2174141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
glass crisper shelf shattered in my hands
replaced shelf with new one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Winston A from Brooklyn, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Raplaced switch
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Selma, IN
- Parts Used:
- 4317943
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Icemaker motor quit
This was a snap. Loosened 3 screws, removed
old ice maker. Made cutout for water chute. Plugged in
wiring harness plug. Installed new ice maker. Tightened 3 screws.
These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.
old ice maker. Made cutout for water chute. Plugged in
wiring harness plug. Installed new ice maker. Tightened 3 screws.
These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Clarkston, MI
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
water dripping in ice cube holder
We removed three screws, unplugged the wire and then removed the old ice maker. Installed the new ice maker with the screws, plugged in the wire and shortly after that we had ice! I was nervous about this repair but it was so easy and the part was here in three days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Clinton from EUSTIS, FL
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
The ice maker only make two cubes of ice per tray
I replaced the old icemaker with a new one but the problem is still occurring in the new one. It only fill with enough water to make about two ice cubes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WARREN from JACKSONVILLE, OR
- Parts Used:
- W10190935
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Stopped Making Ice
Followed on line video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Concord, MA
- Parts Used:
- 4317943
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Would not make ice any longer
I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from New Castle, DE
- Parts Used:
- WP2174141
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The crisper glass insert had broken while being cleaned
Unpacked the replacement crisper glass insert, washed it and placed it in the frame. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Aliki from Miami, FL
- Parts Used:
- WP628356
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Fill cup broke.
Very easy to order from parts select. Took seconds to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Collegeville, PA
- Parts Used:
- W10190935, WPW10190929
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
coating (clear) on ice cube mold peeling off
Removed ice maker from fridge. Removed motor assembly (3) screws on cover, and (2) screws inside. Removed mold (3 screws on bottom) and replaced everything in reverse order. Note: Turned ice maker off for several days while waiting for parts. The water line on this particular model will freeze inside the freezer if ice isn't made for several hours/days. You will have to defrost to begin making ice again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Darcie from VINELAND, NJ
- Parts Used:
- 2159061
- Difficulty Level:
- Difficult
- Total Repair Time:
- 30 - 60 mins
freezing everything
Removed old gasket. Wiped everything down. Popped in new gasket.
It was a little tedious, but it went in easy enough. Some reviews said the new gasket was kinked and bent. Mine I am happy to say was smooth. Some things are still getting quite cold like vegetables and ginger ale.(almost freezing). But it is way better than it was. Saved us from having to purchase another refrigerator. The fellow who helped me made it easy to order and everything went smoothly. I appreciate the help and patience you provided.
I
It was a little tedious, but it went in easy enough. Some reviews said the new gasket was kinked and bent. Mine I am happy to say was smooth. Some things are still getting quite cold like vegetables and ginger ale.(almost freezing). But it is way better than it was. Saved us from having to purchase another refrigerator. The fellow who helped me made it easy to order and everything went smoothly. I appreciate the help and patience you provided.
I
Was this instruction helpful to you?
Thank you for voting!