GX5SHDXVB02 Whirlpool Refrigerator - Instructions

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning on the water supply and bingo...lots of ice cubes.

I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid

Removed the shelf, attached new glide, and replaced shelf

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

It was a very simple operation to replace the parts and required essentially no tools, just a small screwdriver to pry up a tab for removal of the chanel on the front edge of the frame. This chanel had to be removed from the old crisper frame and installed in the new one. In addition the crisper control" had to be popped out of the old frame and into the new frame. Most of my time was spent cleaning.

You just take the old door bin out by sliding it up and replace with the new bin by sliding it down in the door.

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

Remove rail and removed broken black plastic spring mechanism with new one and then replace rail.

First, I shut off the water going to the refrigerator, then removed the ice bin. Then I loosened the two screws on the top of the ice maker (the one toward the front was a little tricky, since you can't see it at all), then removed the screw that fastens the lower bracket to the side of the frig. Then I lifted up on it slightly to remove it from the two upper screws, then unplugged the wiring harness from the side of the refrigerator and lifted the whole unit out of the frig.

I then removed the plastic cover on the front of the ice maker, pressed on the tab to remove the wiring harness from the old ice maker, and installed it on the new ice maker. I then removed the metal arm from the old ice maker and installed it on the new unit as well. The last part that I moved from the old ice maker to the new one was the lower bracket, as the bracket on the new ice maker was bent during shipping.

Once those parts were swapped, I put the plastic cover on the new ice maker, plugged the wiring harness back into the side of the frig, routed the fill tube into the back on the ice maker assembly, and set the unit back on the two upper screws. I then put the screw back in the lower bracket, tightened the two upper screws, and then put the ice bin back in and turned the water back on. After a couple of hours, I threw out the first couple of batches of ice and it is now working as it had in the past.

I also noticed, when looking at the old ice maker, that the black plastic coating was coming off the ice cube tray, so it was a good time to be replacing it anyway. Overall, a very easy job (I was prepared for swearing, parts being slightly off, etc.) and it would have been a shame to have paid someone to do it.

Used socket set to remove screws. Removed the wire harness, then removed lift arm from old ice maker and then put lift arm on the new ice maker. Reinstall wire harness then installed back in freeze with the screws. Video was very helpful. I will do business with Partselect in the future. Shipping was very fast. Thanks Partselect

Easy fix, it's right in the back of the fridge under a cover that just clips in, a piece of foam, and two screws. The hardest part is getting the clips free without breaking them. After replacement it's silent instead of making a grinding noise regularly.

Replaced the rail and slide baskets. Also readjusted the basket. This was extremely easy and saved me close to $500

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

I was getting small sections of ice and a snow like build - up around the freezer door. I thought that the door was not sealing tight enough and that the cold air was leaking out. The original door gasket appeared to not have any flexibility anymore and was getting hard. I ordered a new door gasket from PartsSelect. When the gasket arrived it was in a large enough box and that saved me some time as the gasket was not "crushed" to the point where there were a lot of kinks in the gasket. I used a hair dryer on low to warm the gasket and stretch it out some. The freezer door required me loosening four small screws and lifting the door off. I placed the door on an old blanket so not to scratch the finish. It was easy to remove the old gasket and after doing so I cleaned the track where the new gasket was to go with isopropyl alcohol, Once cleaned, I placed the gasket over the channel in the door where the old gasket had been and started installing the new gasket. I started at the corners and you can feel the gasket snap into place. Once the four corners were done I started at the top and installed the gasket the rest of the way. You can feel it snap into place. as you work your way around the gasket channel. Once the gasket was in place I placed the door on the four small grooves where the door had been and tightened up the screws. I made sure that no white from the inside of the freezer door was showing after the gasket was in place and that the gasket had some "spring" to it. The door was back on, the gasket was tight and it appeared to be a good seal. Around 12 hours later I checked the freezer and there was no more ice or "snow" on the edges of the freezer. While the gasket was not inexpensive, it is a genuine OEM piece, and the gasket is a lot cheaper than a new refrigerator!
I hope this was helpful...