GR2FHMXVS01 Whirlpool Refrigerator - Instructions

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

decided to take a chance and replace the ice maker,so far no water leaking.feels nice to know the problem is fixed.thanks for the video on how to replace it, thanks again very easy repair

Took cardboard cover off rear of refrigerator, five screws. Turned water off and unplugged fridge. Took out two screws holding inlet valve, pulled off quick release power wires and changed out water supplies in and out. Rebooked power and replaces cardboard cover. With power and water back on, ice maker was supplied with water.

First shut off water supply and unplug power. Unscrew icemaker assembly from side wall with 3 screws. Remove front cap and you can clearly see module. Unscrew and remove module ( only three screws). Install new module and revers procedure to finish up. Ice was ready in just a few hours. Video provided by this site was right on and left no questions.

After taking apart the ice maker, the only obvious replacement was the motor assembly. I check various Internet sites and found the best price at PartSelect.

I removed the ice maker from the freezer after turning off the ice make switch. Removal was easy with only one screw holding in the entire assembly. The ice maker has rails that allow it to slide in and out like a drawer.

After R/R the motor assembly and returning the ice make to the freezer all that remiand was to see if it worked.

Within 10 minutes I had the wonderful sound of water filling the ice maker tray. Within 30 minutes of that, ICE!!!

Shopping, ordering and shipping of the part was fast and efficient. I'll go with PartSelect for all my future appliance needs.

Took the old one out and plug the new one in, simply as 1 2 3. Order the part one morning,it was here the next afternoon, the ice maker was fixed in less than a half hour. we will order from you the next time.

I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.

It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.

take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.

I recieved the replacement part the next day after ordering it. If you are some what mechanicaly talented this repair is very simple. The only tool that is needed is a nut driver. You may want to remove the bracket holding the water solenoid vavlves. Then you can pull them out of your way to remove the 3 screws holding the fan to the bracket. Once you remove the old fan motor just reverce your steps with the new motor. Check that all your screws are tight. Check to make sure that there are no wires in the way of the fan. Don't forget to attach the wire harness and re-attach the solenoid bracket. Ahh nice and quiet like new!

pulled fridge out, remove back cover, remove 4 screws holding fan put new fan in with new screws way easy dont call a repair man for this shipping was fast thank you for that

Simple remove the fan and motor, plug in the new cord and screw in the new motor.

pulled out gasket and then had to put new gasket in place. Took door off laid it on the kitchen table. Used the small rounded end scissors so that the gasket would get perforated.

Took the glass shelf out of the fridge in our rental home to clean and it just shattered in our hands. Did a search online and found part select, phoned to make sure I was looking at the correct part, the lady on the phone was very helpful. I ordered the shelf using the next day service as we were returning home to the UK within 3 days so did not want to take the chance of not receiving it before we left. I got the notification the part had been dispatched, the part was delivered early next morning. Took the shelf out the package and placed in the tray, job done!. Great service will definately use again, have book marked the site.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!