GI5FVAXVB00 Whirlpool Refrigerator - Instructions

Really easy, simple instructions, and it was on my doorstep 3 days after I ordered. Much simpler than dealing with the appliance store, where I'd have to drive to the store, order the filter, wait 7-10 days, and return to pick it up. Ughh! Internet is the way to go!

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

Removing the ice making assembly from the Ice compartment was not difficult except that two of the 3 screws we not visible without a mirror and then my nut driver was 5" long making it very tight quarters, so it was a time consuming process to remove them.
Once the 3 screws were removed the wiring harness was easily disconnected and the whole assembly came out.
The next step was to figure out how to remove the faulty part from the rest of the assembly.
After some strong persuasion the part would not separate from the control Assy. (The front of the unit) To complete the job I had to pull the front cover and unplug the motor and heater assy to expose two additional screws that had to be removed to pull the defective part out. The reassembly went quite easy except the 2 screws that you need a mirror to see. I was also trying to hurry because the frozen items were not holding all that well after the door was open for about an hour and a half. An instruction sheet showing the steps would have cut the time over 1/2!

I was amazed when Fed Ex pulled up to our front door the following day after I ordered the parts, I was wondering what they were delivering and to my amazement it was the parts I had ordered from parts select the previous day , thank you so much , you are awesome. My 73 year old husband who is a 5 year cancer survivor had the part installed and we were ready to start making ice within 1 hour.He went by the installation information sent in by your customers. Thank you all, Jo Mesplay

unscrewed old filter, screwed in new....good to go!

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

Removed and disconnected the icemaker, cleaned all areas and disassembled the failed parts. Reassembled with the new parts inlcuded with the purchased package and resinstalled the unit. Started the unit and chedked for proper operation. Successful repair.

I first turned off the refrigerator. I then used a hair dryer to melt and release the ice by warming the bottom of the mould. Then I turned the fridge back on and let the icemaker discharge the ice. I then turned off the icemaker and ordered the new part. I unplugged the fridge, removed the icemaker (three screws and an electrical connection). Then I replaced the heater/tray with the new one and turned everything back on. Within a couple of hours we began having ice again.

inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."

Everything went as planned except the cold temperature (freezer door switch located inside freezer) made deflection of the switch locking tab difficult to remove. Letting the switch warm up was not an option.

Went to You Tube - found how to change out - the only problem I had was programming the new circuit board. Went to Maytag site and found out how to reprogram in a step by step instruction and it worked.

Unplug fridge, turn off water to fridge
Uninstall ice maker (some tools needed)
Remove ice buildup inside water line

Purchase new ice maker and installed it while watching a youtube video of how to do it. Once installed, turned on the water line and plugged in fridge.

Removed the shelf below the cover to allow plenty of room to work spread apart the old cover at the pivot point toward the back installed the new one in reverse order

The switch fix but did not fix the problem. I assumed the wires go on the same way as on the old switch. Is it possible if one light Burns out, the other will not work either?

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now