G25EFSB23S5 Whirlpool Refrigerator - Instructions

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

Watched video on line.

An ideal opportunity to clean the tracks for the glass top and sides. I just removed the two (2) screws with nut driver and gently eased the end cap off by slightly pulling it forward and up, inserting the lid onto the new endcap and slipping the cap back into place securing with the two screws. as easy as pie. I did not change the right end cap as there was no need for it, But if U have to change it U must also first disconnect the back plate.

I removed the drawers and glass shelf that are over the pantry drawer as well as the small piece that allows the drawer to pull in and out. Then I simply snapped the old one out, snapped the new one in, replaced everything I had removed and Done! Took less than 10 minutes.

I replaced both side. The left side I very easy to replace. It has 2 screws holding the end cap in place and the tracking has 2 screws holding it in. Undo the 4 screws and put the track on the new end cap and then you are good to go to install the new end cap on the left side. Now for the right side is easy, but you now have to also undo 2 screws and other 2 for the track just like left side but also you are going to have to undo the humidity control stuff and put it on the new end cap.

I just watched the YouTube video that you guys provided and did it exactly step by step and it was perfect

Thank you for the prompt delivery. I thought it was going to be a big problem to get a replacement shelf, but I ordered online and had my part in 3 days! Very easy to insert. Did lay carton on the floor and pulled out the insert. At 83 my strength isn't what is used to be, but it came out pretty easy. I am beyond thrilled with the service. Thank you.

Replaced seal on door. Same problem. Went to Lowe's and got several magnetic cabinet door catches. Attached them to the top of the door. (they can be seen sticking up), with the magnet part screwed to the door and the metal plate attached to a small wooden block glued to the top of the body with contact cement. Cost abound $16.

"To infinity and beyond."

Heated new gasket in dryer. Removed old gasket. Took less than five minutes per door and I am 78 years old!

Was easier than I thought it would be . Thanks to your diagrams for the parts.

Put the gasket in the dryer for 15 minutes to warm it up. It fit much better after it was warm.

No product was sent in the box for the shaft I received an empty box from them cannot perform any repairs because I got no product from this company. Called customer service said due to Covid no customer service available when online and receive no customer service no refund no product no help

Replaced the rail and slide baskets. Also readjusted the basket. This was extremely easy and saved me close to $500

Really easy - Remove drawers, remove glass shelf and associated support rails, remove drawer slide from old endcap, remove old endcap, reverse proceedure installing new endcap - now the hard part, have a cool softdrink while you carry the old endcap and packing material from the new one out to the trash.

By the way - the part got here really fast - thanks for the great service.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!