GS2KVAXVS00 Whirlpool Refrigerator - Instructions

First I removed all food in freezer.Then removed selves and hanger brackets.Then the back panel and light cover.Then I unplugged motor but before this I unplugged refrigerator from the wall.Removed motor from bracket after pulling of fan. Reversed the order to install motor and put back together

Removed screws, unplugged connectors to the two faulty circuit boards, reconnected both cables to new/replacement circuit boards, reinstalled screws. Extrremely simple! Worked perfectly! Saved about $150 in less than 30 minutes. Great, fast service by PartsSelect.

First removed the three screws at the top that holds the door at the top. Removed the worn out lower door cam after removing one screw. Did the same on the door closing cam (in fact this cam has worn and broken into two pieces). Replaced with the new ones, put the screws back, mounted the door and replaced the three screws on top. The door closed perfectly.
Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!

"Popped it in".

Built-in filter was corroded due to age. New filter corrected problem.

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

Old part would not stay in place (broken). Recieved new part and snapped it in to place . No tools needed.

I FOLLOWED A U TUBE VIDEO. IT WAS ALMOST PERFECT FOR MY SIDE BY SIDE REFRIGERATOR.

took apart panel from door and removed old part and installed new part.It's difficult if you have big hands. Best if you have someone hold up wire panel while you are installing.

It was great repaired the problem for under $60

Unplug, then on the freezer side, remove the drawers, then remove the screws holding the sheet metal cover, remove the rails (for the drawer) that interfere with removing the sheet metal cover. pull the wires off the motor. There is a big plastic piece that holds a small plastic piece that holds the motor. Remove the plastic piece that holds the motor/fan (you might be able to swap the motor by removing the little plastic piece that holds the motor, or you can remove the bigger piece and then remove the small piece that holds the motor). Pull the fan blade off (to reuse), swap the motor. NOTE - the new motor wire terminals may be on the opposite side of the motor vs. the old motor - that is not a problem - there is plenty of room for the wires. After the motor is installed put the fan blade back on, reinstall the removed plastic pieces in the back of the refrigerator. Now, I'd suggest a quick test. Make sure the new motor works and the fan blows before you button it up. Once you know it works, power it off, and put the sheet metal cover back on, reinstall the basket brackets, put the baskets back in place, close the door, and turn it back on.

Easy!!!!! Just cut the power to the unit and unscrew the boards. One is to the right of the ice maker and one is to the left. Snap the connecter on the old board so it will disconnect and replace it. It works perfect now. I had a service man come out and he quoted me $400.00. He told me I needed a whole new ice maker too. Not true. I simply email you guys and had the part in 3 days. It only cost me $80.00. I will use your site for every part I need. Thanks

My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causing the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.

Super-easy... First, empty refrigerator door. Then, just remove the bolt that goes through the cover over the top hinge. This exposes three more small bolts. Remove these and the top hinge assembly will lift off. Lift door off. Remove cam from door and lower hinge, slip new cams on, and reassemble. The hardest part was pulling all of the junk stuff out of the refrigerator door. Who know you could accumulate so much salad dressing?

Removed the top bracket (3 5/16 size hexhead bolts)
Lifted door free of the bottom cam and hinge socket
(after, of course removing the items from the door shelves!)
removed one bolt holding the lower came to the cabinet.
Pried the cam loose, replaced with new and re-bolted
removed one bolt from cam on door - unable to remove cam until I removed the guard bracket (two more bolts)
worked the plastic cam from the door by twisting it and pulling the socket from it's hole.
Slipped the new cam into the socket hole, aligned the bolt hole and bolted it tight.
Aligned the top cam to the bottom cam as I replaced the door. Re-attached the top bracket.
All bolts were 5/16
Door now works perfectly again.

I called a local appliance repair / sales store and he told me what to look for. There is an electronic "eye" on the "On / Off" panel in the freezer, and there is an electronic eye that sends a beam across to the other side where there is a receiver. If there is no beam, or the beam is obstructed --- for example when the freezer door is open the little "door" on the opposite side of the On / Off switch opens, interrupting the beam --- the icemaker will not work. In my case it was easy... there was no beam being sent across, so I KNEW it was bad.

Ordered the part, took out 6 screws total to remove the sender and receiver, removed the circuit boards with 3 more screws, replaced with new boards, and reinstalled.

Trust me - a 10 year old could do this. Don't be afraid because it involves "circuit boards" - it's literally one or two screws, replace the boards, screw them back in, and plug the two sides back in. ANYONE can do it... anyone!!!