GI0FSAXVB00 Whirlpool Refrigerator - Instructions

Placed new gaskets on hot patio to smooth them out. Took minion bar off and removed door gaskets. Replaced new gaskets, and minion bar.
Took freezer door off and replaced gasket. I had problems with the first set of door gaskets but customer service replaced them in record time. Service was outstanding. 5 Stars

we removed all the lower stuff,so we could get to the part.
unscrewed all pieces 3 screws
than removed it all in order..
than the hard part came ,when we had to figure out how to remove all the moving parts.from the back ..after a little wiggling we figured it all out and got a part...the new piece in and all back together...my husband and i did it in about 45 minutes,,,also gave us a chance to get those really hard places in the back to clean...thanks for all your help in helping me id the part..
thanks
linda landsdowne

Remove crispers & bottom drawer. Removed glass piece. Unscrewed piece( small nuts not screw heads) There is also a nubbie at front. You must remove by sliding out & lifting back of part. Reuse screws to replace piece & drawer runner. It took 15 to 20 minutes. I am all thumbs. If I can do anyone can do!

The peg on the door broke off the left end cap. This seems to be a bad design on the part of amana. It's happened twice now. Very fragile. The repair was so easy that my wife tackled it while I was at work because I was too busy to do it. She said the only problem was removing all the trays, shelves, and drawers out of the fridge and putting that back together which is a bit cumbersome and tricky. The actual part removal and replacement is straight forward once the other stuff is removed to get to the screws that are holding the end cap on. When I did it for the right end cap it was a bit more challenging because there were more parts that had to come off and go back on. I am happy that this can be easily repaired, but not happy with amana that the sliding drawer and door are so susceptible to breakage at the two pegs. This is a flaw in the design.

Watched video. Unplugged refrigerator and popped out switch. In plugged connector and pushed switch in place. Plugged in refrigerator and the light worked

Removed the 3 screws that hold the ice maker in place and remove the cover and level wire. Put the cover and wire on new part and install the 3 screws. Had ice within 1 hour. A very easy job for the do it yourselfer. Suspect the heat coil that melts the cubes was not working in the old unit and cubes stayed in the tray.

A jar was dropped on the chef's pantry lid and cracked the lid. I unhinged one side of the lid from the pantry drawer by gently pushing outward on one of the hinge pins. The lid slid out easily. I then reversed the process using the new lid and it went in smoothly. Be sure to align the lid so it rests on the shoulder of the pantry drawer. Simple task, no tools, and less than 5 minutes effort. The replacement part was perfect.

The old cover was off and I just slid the replacement part that I got from you'll, it just slid in place and snapped close. Perfect fit. Thanks guys

I initially tested the heating element and defrost thermostat using an ohm meter. the defrost thermostat was incased in ice, so I replaced it first. The refridgerator worked for about a week and then froze up again. I then replaced the thermistor and the unit is working as designed.

removed old ice maker by taking out a couple of screws in the back of freezer,when new ice maker arrived i saw that it didn't have the same hose apparatus as old one so I easily took apart old one then took apart new one and switched them out-very-- easily done for a 61 yr old lady I might add-- also had to reinstall ice maker arm off old ice maker as new one does not come with one Then installed new ice maker in freezer I am very very pleased,sure saved a lot of money doing it my self

This was the third icemaker replaced since January 1999. Improvement need to be made in the design of the icemaker so that more than 2-3 years of life is available.
The most difficult part was disconnecting the power plug in the back of the icemaker. You must squeeze the upper and lower tabs together and pull out at the same time to disconnect. Once this is done, take out one nut head screw, lift up on the icemaker and remove from the hanger. Be careful that you don't break the plastic tabs on the hangers. Replace new icemaker in reverse, feed water supply where it must go in the back, resnap onto hangers, replace the nut head screw and snap in the power plug. It took about 2 hours before the icemaker began making ice. It has been working fine ever since. PS. I saved about $200.00 over having a repairman come in and replace the unit.

Unscrewed all related parts and also took out drawers and glass shelf. Reused plastic slider which raps around right corner to the back wall of the unit. Make sure to remember how this plastic slider fits into the new end cap, it is a little tricky putting it back without cracking it. Suggest take a digital picture as to how it fits together before taking the slider out of the old end cap. Reinstall same way as you took it out. Good time to clean while everything is out of the bottom of the refrigerator.

Remove 1 screw under ice maker. Gently pull downwards to unhook ice maker. Disconnected 4 pin wire connector. Remove and set aside the cover and wire loop you will need on new ice maker. Reverse the steps to install new maker. Once new ice maker is installed you will have to wait 2-4 hours for ice. There is a thermostat that will need to reach 10 degrees F to operate.

Saw U tube instrctions how to install and it was easy

I removed the right side endcap and rear thermostat piece behind the pull out drawer. It was fairly quick, 3 screws on the exterior of the end cap and one screw holding in the drawer thermostat. The worst part was getting the thermostat control that connects the drawer thermostat control to the rear thermostat. After playing with the control rod I was able to to snap it in successfully to the endcap with the proper rod connection. The rear thermostat goes in first, then the endcap. Quick and easy. For $23 it would have cost over $150 to call a repair guy ($120 call charge plus parts). Thanks.