G25EFSB23S8 Whirlpool Refrigerator - Instructions

Cut old fill tube into pieces, removed and replaced with new tube. Extremely easy.

It was easier than I had anticipated. Just had to make sure that I was very careful in removing the old part so I did not break any of the good plastic that I needed in order to install the plastic temperature control to the new part.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

First I removed the pantry drawer; then the two crisper drawers and glass shelf. Then I removed the hex screws that held end cap in place. Removal of cap from refrigerator was complicated by the adjustable temperature control - it is loosely attached at the back of end cap and also has to be removed to get cap out. Gentle persuasion accomplishes this. Getting the slider off end cap also a bit difficult. Then I removed the drawer glides. Reversing all steps was fairly easy and the rest of the "fix" went well. I wished that there had been some written directions - or at the very least, a diagram of how all went together. All in all was still cheaper than repair person.

Let the ice in the freezer melt while installing P trap drain tube

Switched the drain out using the video tutorial
Fixed the problem
Have had no more drain issues

When the gasket is delivered it will be folded. You will need to unfold it and leave it on a flat surface for several days. Keep it as square as possible, and heat the kinked portions with a hair dryer on high heat and slow fan while molding kinked portions with your hands for 30 to 60 seconds at a time. Do that 2-3 times per day. When it looks 90% uniform with the non kinked portions, you can install it. Installation takes less than 10 minutes. Clean the metal edge of the freezer well. I recommend taking the door annd frame off (This is remarkably easy. THe door and frame pretty much lifts up and out after you hold the rail clips inward) because the lower edge is so close to the floor. The just pulll off the old gasket. There are no screws or clips. Starting in any corner, press new gasket into place. Go around the perimeter several times to make sure it is pushed in fully and evenly. Then reinstall the door and frame.

Empty drawer and take out . remove glass shelf and front and rear shelf braces. remove 2 screws holding pantry end cap to fridge. remove rear bracket by unsnapping clips. remove temp control arm. and reattach to new end cap. reinstall rear bracket to fridge and align end cap, align screws and tighten. reinstall drawers and shelf brackets. replace glass shelf. and reattach lid to brackets. Open beer and enjoy success.

My non mechanical husband used a flat edged screwdriver to pry out the broken switch. Then it was a matter of reconnecting to small wires and popping the switch back in place....voila, life has been great ever since. ;)

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I made a temporary repair by drilling the old blade plastic hub and put a small screw in it to hold it on to the shaft until the new blade arrived. The new blade came in within the two days I needed before Thanksgiving. I removed the old and pushed on the new. There were 8 screws on the back guard and two to hold the motor on. It was a snap.
Thank you PartSelect.com The wife is very, very happy now, we had 51 coming over for Thanksgiving. :)

Remove the grate at the back of the refrigerator. Remove the existing drawn tube. Replace the exiting drain tube with the updated drain tube. Check to see if water was draining properly. Replace the grate. Sit back and have a beer.

You remove the white frame from around the old pan by popping it off from the bottom being careful not to break it. Install it on the new pan using the reverse procedures. Popping it on starting at the bottom. Very easy

Center Rail:
Removed the crisper drawers. Removed contents and the glass shelf above the the crisper drawers. Positioned the center rail as shown in the diagram, but it was not an easy fit so afraid it might get broken by forcing it, rolled the front edge of the glass shelf support slightly outward which enabled the rear tab of the rail room to engage into the rear shelf bracket and the "front tab" of the rail to slip into the notch at the front edge of the glass shelf support.

Pantry Drawer and Lid:
Lid was already long gone so I just slid the cracked pantry drawer out of the refrigerator, cleaned the surface under the drawer, placed the new drawer on the slides and in it went. The drawer lid was another finesse it in without breaking the hinge tab so had to position it slightly on the diagonal and popped it into place.

Now the crisper drawers glide silently and effortlessly along the side rails with the new center rail in place while the deli drawer lid raises itself automatically with a gentle grasp of the drawer pull.

It had been so long since those parts had busted I had forgotten how the assembly was supposed to work. It's like having a new refrigerator.

Now if I could just manage the ice maker!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.