ED5LHAXWS02 Whirlpool Refrigerator - Instructions

That was due to the evaporator blocked by the ice. Check found the defrost timer is okay. The next thing I can think of is to replace the Electronic Control Board which is installed in the fridge side top compartment. Ply open the face cover, remove the nut and screw that secure the EC Board. Pull out the cable, mount the new card and re-connect. So simple. It is back in order.

This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.

Same as everybody else on this post. Real easy. Actually, I just wish I would have done it sooner.

i took the cover plate off the inside of the freezer under the ice bin[two screws] then I disconnected the wiring harness, then removed the four screws to remove the motor and then put the new motor in and the ice dispenser dispensed ice. Less than 1/2 hour with only needing a nut driver,and a flashlight.

Removed front plastic grill and screws holding the filter in place. Also removed lower back cardboard panel to access water lines. Video on this website told me how to remove water lines from filter, you must depress a collar around the water line while pulling out the water line. Then install the new Water Filter Housing and water lines. The only problems I had was the tight space to work in and one of the water lines was leaking, but pushing the water line in further solved the problem.

Resistance on solenoid for water to ice maker measured low (5 ohms). I assumed the coil insulation had degraded because there was almost a short with such low resistance. Replaced the water inlet valve kit and ice maker filled with water and everything worked great. I had to cut the ends of the hoses because my model use compression fittings and this new valve kit used the push on fittings. No leaks no problems. The cables plugged in the opposite direction from the old valve kit, so I had to re-route the cable a little and create slack by removing from 1 cable clamp.

remove shelves in freezer compartment incl.holders(slide up to remove)
Remove lamp/shield
Remove panel (six phillips screws)
disconnect motor
pull off fan blade
squeeze bracket holding motor to remove
remove motor.
Re-assemble (in reverse)

First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.

This is in a rental house; Refrigerator/freezer has been off for a few weeks so just opened the freezer door and used screwdriver to pry out one corner then pliers to grab and pull old gasket (seal) off. Had the new one laid out overnight to relax it; placed one corner on and then the opposite corner then repeated the other two corners. Positioned the keeper edge plastic all of the way around to place the gasket in the door. Closed the door to check the seal and plugged unit back in. Waited and then checked air temp with hand held IR temp gauge. All checked good, no cold spots anywhere. Piece of cake!

Approximately:

1. Unplugged refrigerator.
2. Emptied Freezer.
3. Removed Ice Maker.
4. Waited a few hours for ice to melt around back panel & nuts.
5. Removed back panel and the cover over fan and fan motor.
6. Waited many more hours for ice to thaw over fins, wiring, etc.
7. Easily replaced the bi-mental defrost thermostat.
8. Replaced panel, fan cover, ice maker.
9. Plugged in refrigerator and waited a bit.

This worked! Yahoo.

p.s. I am a 65+ year old mechanically minded woman. :-)

Removed catch tray and then removed two screws that are underneath. I left the control panel hanging from its wires, then removed the two screws from the control bracket.
A word of caution before next step: You need to remove the two micro switches on the left and right. While trying to remove one, it split apart and the pieces fell out. I was able to put it back together and it worked fine. So be careful with the micro switches.
Continue tranferring wires and switches to the new bracket and reassemble in the opposite order.
An easy repair.

First, verified power supply. I have power at wall outlet, no power at compressor. Also noticed no condenser fan operation. Searched YouTube and watched a few diagnostic videos of how to test for proper operation of my model. Dropped the control panel down to reveal the thermostat switch and control board. Wiggled thermostat knob and compressor would work intermittently. Thermostat bad internally. Removed wiring connections, removed cover over temp.probe. slowly removed capillary tube. Removed plastic sheath from tube. Take your time installing new capillary tube into plastic sheath as not to kink and damage tube. Route the new tube back into position that the old one was in. Reinstall covers. NOTE: My wiring terminals on the new switch were in different locations but the switch was the same dimensions. I used a multi-meter to determine the correct wire locations on new switch and installed. Reconnected power and all works well now.

Removed upper hinge cover and hinge, lifted door from lower hinge socket, removed lower cam from 'frig hinge, and replaced with new. I had a helper hold the 'frig door while I removed old upper cam, and replaced with new. Piece of cake and works like new! This must be a design problem..

Removing the panels inside the freezer section was the most difficult ,because it is narrow,hard to fit your body inside compartment, in order to cut wires and to splice Bi-metal Defrost Thermostat wires (2 ) Watch the videos on the web site so you know where to start. First time I ever "repaired " a large appliance, saved me over $ 600.00 (that's what the people I bought the Refrigerator from wanted to charge me.) My parts cost 65.00 !!!!! My younger brother turned me onto the web site... , I'll be returning to the site and telling my friends about it. It's a total "rip off" what service organizations charge the general public these days from Car Dealer ships to the stores we purchase our appliances from. !!! Glad I still have my health and faculties to repair the essentials we have around our homes. !!!!

New part slipped right into the studs and fit perfectly