BRS62BBBNA00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Thomas from Clearwater, FL
- Parts Used:
- W10823377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Chute Mechanism broke / air flow into ice maker
Have not installed yet as I'm on a quick TX-FL-TX turnaround. Bought and received the part in 24 hours...great. Order contained no instructions. I could probably figure it out myself just have not attempted yet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DANIEL from DAVENPORT, FL
- Parts Used:
- WPW10121138
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Water filter housing wasn't let the water go through the filter
I got model number off my unit and order the part. That was after trying a lot of different filters first. I did a rush order so I got it in 2 days. Pulled the unit out to shut the water off. Then took the back off so I could take the 2 screws that hold the water value . That way I wouldn't have to go back and forth. Now I went to the front. I already had had the vent cover at the bottom of the unit off. I had a head lap on so to make it easier to see under the unit. Then I use the nut driver or you can use 1/4 inch drive ratchet with sockets. To take the 2 screws out that hold the filter housing. Then lift the spring wire that is on the left side of the release botton. Then push the wire up out of the way. Reach back and pull the water value forward so you have slack in the water lines. Now you can pull the fliter housing out to you. Now release the 2 water lines by pushing down on the rings around the water lines and hold while you pull the water lines out. Now the old water filter housing is free you can set it to the side. I inspected the new filter housing for any deformities and cracks before I started installing. Now I hooked the water lines up by pushing them into the right size spring ring hole. Once lines was all the way in I pulled back on the water lines to make sure they were locked in place. Then I put a new water filter in and turned the water on to make sure of no leaks. Then I put everything back together in the reverse order I took it apart. Then I check the spicket to make sure everything was working right. After that I was able to push the refrigerator back in and then wipe everything up and I was done.
Was this instruction helpful to you?
Thank you for voting!
My Crisper Draw side railing had broken
I ordered the 2 new drawers, the crisper pan and the meat pan with handle. I took them from the box, wiped them out and slid them right into the spots where my previous drawers were. End of story. This took less than 5 minutes to install. I used the chat feature to inquire as to what number items that I needed to order these 2 drawers, was given the numbers and order the items on line right then. Easy They arrived in record time, like maybe 2 days. They were well packed and arrived in pristine condition.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Pasadena, CA
- Parts Used:
- WP2260518W
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Water Filter Cap
Took the broken cap off. Actually it practically fell off. Put the new cap in place, turned it to the right and Presto! it locked in and works fine. It took longer to get it out of the box than it did to install it :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Lewisville, TX
- Parts Used:
- WPW10329686
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Refrig Door Cams wore out and made noises when opening and closing.
Followed Door Removal instructions by removing the Top Screws from the Cabinet. Lifted Door OFF the Metal Hinge. Unscrewed both Lower and Upper Cams from the Hinge and Door. Replaced with new after coating with Vasoline. Lifted Door back in place with help from Wife. Only problem was guiding the Door back onto the Hinge. Works fine. Two year old Frig. This is a design problem, as the cams should last longer than 22 months.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Mt Juliet, TN
- Parts Used:
- W10823377
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Plastic door bracket for icemaker chute broken
Googled with question about how to get to the repair as there were no screws on the faceplate. Found I had to lift the faceplate at the bottom and pry out. Was kind of hard to get the long spindle back through the ears of the bracket holder along with getting the spring of the door lined up for the spindle to pass through to the other side. Finally got it right and then just put it all back together. Frustrating at first but I had to get it done as my wife was tired of having to take large clumps of ice out of the ice tray..three years wait for the repair. That door being open let warm air in and let the ice melt just enough to stick together in a clump. All is well now. Longer you wait the more appreciative she is however. ha
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Heathsville, VA
- Parts Used:
- W10508993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Crisper drawer tilted to the right when pulled out
The repair consisted of lifting up the drawer cover and replacing it. Why the 60 minutes to do that? It took 58 minutes to clean the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jairaj from North grafton, MA
- Parts Used:
- WP2182179, WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The refrigerator door was hanging low and not closing properly. Hence the refrigerator was not maintaining the temperature
First removed the three screws at the top that holds the door at the top. Removed the worn out lower door cam after removing one screw. Did the same on the door closing cam (in fact this cam has worn and broken into two pieces). Replaced with the new ones, put the screws back, mounted the door and replaced the three screws on top. The door closed perfectly.
Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!
Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Monica from EDMOND, OK
- Parts Used:
- W10823511
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
water leaked when the paddel was pushed
Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALAN from ASH, NC
- Parts Used:
- WP2180224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Tab Was Broken On Ice Guide
Old part would not stay in place (broken). Recieved new part and snapped it in to place . No tools needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Danville, VA
- Parts Used:
- EDR3RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
No water to ice maker
Built-in filter was corroded due to age. New filter corrected problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daisy from MIAMI, FL
- Parts Used:
- W10823377
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice tray and door funnel woulf freeze
took apart panel from door and removed old part and installed new part.It's difficult if you have big hands. Best if you have someone hold up wire panel while you are installing.
It was great repaired the problem for under $60
It was great repaired the problem for under $60
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Fort Collins, CO
- Parts Used:
- WP2182179, WPW10329686
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set
Refrigerator door of our double door not closing
Removed the top bracket (3 5/16 size hexhead bolts)
Lifted door free of the bottom cam and hinge socket
(after, of course removing the items from the door shelves!)
removed one bolt holding the lower came to the cabinet.
Pried the cam loose, replaced with new and re-bolted
removed one bolt from cam on door - unable to remove cam until I removed the guard bracket (two more bolts)
worked the plastic cam from the door by twisting it and pulling the socket from it's hole.
Slipped the new cam into the socket hole, aligned the bolt hole and bolted it tight.
Aligned the top cam to the bottom cam as I replaced the door. Re-attached the top bracket.
All bolts were 5/16
Door now works perfectly again.
Lifted door free of the bottom cam and hinge socket
(after, of course removing the items from the door shelves!)
removed one bolt holding the lower came to the cabinet.
Pried the cam loose, replaced with new and re-bolted
removed one bolt from cam on door - unable to remove cam until I removed the guard bracket (two more bolts)
worked the plastic cam from the door by twisting it and pulling the socket from it's hole.
Slipped the new cam into the socket hole, aligned the bolt hole and bolted it tight.
Aligned the top cam to the bottom cam as I replaced the door. Re-attached the top bracket.
All bolts were 5/16
Door now works perfectly again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Arlington, TX
- Parts Used:
- 4387478
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Lower Light Socket removed and Wires capped with wire nuts
My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causing the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephen from Fresno, CA
- Parts Used:
- WP2182179, WPW10329686
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Refrigerator door wouldn't self-close
Super-easy... First, empty refrigerator door. Then, just remove the bolt that goes through the cover over the top hinge. This exposes three more small bolts. Remove these and the top hinge assembly will lift off. Lift door off. Remove cam from door and lower hinge, slip new cams on, and reassemble. The hardest part was pulling all of the junk stuff out of the refrigerator door. Who know you could accumulate so much salad dressing?
Was this instruction helpful to you?
Thank you for voting!