7WSC21C4XA00 Whirlpool Refrigerator - Instructions

The holder is held in place with two screws. Once you have it unscrewed you can snap the old sockets out and replace them.

Ordered new sockets and presto, the lights work again.
They just snapped into the holder and the holder went up with two screws.
HINT: I did take a photo of the 4 electrical connectors AND labeled each one with a Sharpie 1, 2, 3, and 4 from left to right.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

While trying to get my icemaker to unjam (ice all stuck together) I broke the coupling under the ice bin. Shouldn't have tried to force it, but you learn from experience...
I found the diagram of what I needed to order on the website and ordered the part, which arrived in about 2 days. Dumped the ice out of the bin, removed the screw that held in the broken coupling, replaced the coupling and replaced the screw. Put the ice bin back into the freezer door and Voila.. ice dispenser works again.

Removed one screw that hold the cuopling and installed the new one. That it

Very simple fix, remove 3 screws, two connectors to the old switch

Open door and from appliance instruction book
Replace filter

I pulled the wiring harness off the bad motor, removed the fan blades (it was just a press fit and can be pulled off by hand), took out the three screws. The fan on the replacement motor had to be installed out of the fridge. I wiggled the new motor into place and installed the three screws. I cut the wiring harness off the fridge side and cut back the insulation. Using wire nuts I reconnected the wiring. I plugged the fridge back in and it worked like a champ.
The repair went fairly easy. The motor was a bit difficult to get into tight space with my big hands. The wiring harness on the fridge side had to be cut and wire nuts used to reconnect the wiring to the new motor but it was pretty straight forward. Over all the repair was easy except for being in a tight spot. I recommend trying to fix it yourself, you may supprise yourself and save some serious bucks on labor cost to boot.

Open the refirigerator door and push and hold the On/Off button at the top to turn off internal power. Open the freezer door and move the icemaker switch on the right side freezer wall to "off".

To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.

The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet.
Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.

Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.

The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.

Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.

Once the motor module is seated, replace the 3 screws and push the white cover back on.

Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.

Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.

The icemaker should start making ice within 2 hours.

Emptied the ice holder, then removed the two screws located in the bottom of the ice holder. they were holding the metal cover in place, once removed I was able to remove the entire rotating ice prongs which moved the ice into the chute. I had to do this because the screw that held the coupling on could not be removed (too tight) Once the entire rotating device was removed I could easily remove the screw and replace the entire assembly.

Used u-tube video to review steps in making repair. Wires shorter than described but after looking at replacement sockets difference was clear.

Removed and disconnected the icemaker, cleaned all areas and disassembled the failed parts. Reassembled with the new parts inlcuded with the purchased package and resinstalled the unit. Started the unit and chedked for proper operation. Successful repair.

The only real difficultly I had replacing the ice door was getting the exterior trim off the freezer door. You have to push down on the bottom of the trim to release the tabs that hold it in place. After removal of the trim, the rest of the repair is pretty straight forward.
The ice door kit solved the problem!

I was amazed when Fed Ex pulled up to our front door the following day after I ordered the parts, I was wondering what they were delivering and to my amazement it was the parts I had ordered from parts select the previous day , thank you so much , you are awesome. My 73 year old husband who is a 5 year cancer survivor had the part installed and we were ready to start making ice within 1 hour.He went by the installation information sent in by your customers. Thank you all, Jo Mesplay

****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and access panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years

Simply remove the small screw frome the bottom of the bucket, slide the coupling onto the screw shaft, and retighten the screw.