7GSC22C6XY00 Whirlpool Refrigerator - Instructions

Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.

Instructions were great five minutes to remove and replace fan....Thank You............ saved big money

ordered new filter, removed old filter from fridge, and installed new one

Googled "intermittent clicking noise" or something similar and consensus was it was either the capacitor or compressor start relay. You-tubed videos on how to replace these. Looked easy. Just unplug them from the condenser and replace. Contacted Part Select and staff said 50% of the the time it was the capacitor, 50% of the time it was the relay. I was in a time crunch so I ordered both and they came in a couple of days. I replaced the capacitor but the clicking noise continued. I replaced the relay and problem solved! Maybe I could have gotten away with just replacing the relay, but I had them both by then and figured with a 10 year old fridge, better replace them both at the same time and be done with the problem. So far, so good.

Unplug, then on the freezer side, remove the drawers, then remove the screws holding the sheet metal cover, remove the rails (for the drawer) that interfere with removing the sheet metal cover. pull the wires off the motor. There is a big plastic piece that holds a small plastic piece that holds the motor. Remove the plastic piece that holds the motor/fan (you might be able to swap the motor by removing the little plastic piece that holds the motor, or you can remove the bigger piece and then remove the small piece that holds the motor). Pull the fan blade off (to reuse), swap the motor. NOTE - the new motor wire terminals may be on the opposite side of the motor vs. the old motor - that is not a problem - there is plenty of room for the wires. After the motor is installed put the fan blade back on, reinstall the removed plastic pieces in the back of the refrigerator. Now, I'd suggest a quick test. Make sure the new motor works and the fan blows before you button it up. Once you know it works, power it off, and put the sheet metal cover back on, reinstall the basket brackets, put the baskets back in place, close the door, and turn it back on.

Took it out of the box. Emptied the ice out of the broken bin. Slid the new one in and all done.

Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!

1. Removed 2 screws on top hing.
2. Easily lifted door and place on table.
3. Removed set screw for door cam.
4. Removed stop bracket.
5. Reversed steps 4 thru 1.

When tightening top 2 screws, make sure door gap is consistent and top of frig door aligns with the top of the freezer door.

NOTE: The lady at PartSelect who helped me with my order was great. Took the time to verify my parts. Prior to this I had bought the part from a nearby appliance parts store. They sold me the wrong part, even though I showed them a picture of my model number plate b4 ordering. In the future, I will always go to PartSelect for my appliance part purchases.

Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80...would have been at least $100 to have a repair person come to the house!

Unplug power to refridg/freezer. Removed the screw in rt. rear bottom of ice maker to remove. After removing slightly, unplug pigtail. Remove ice maker completely. Remove large square cover from left side to expose motor. Remove screws to remove motor. Replce with new. Replace ice maker to freezer, plug pigtail back in, put screw back in rt rear bottom, plug refridg/freezer back into power source. Ice was making in about 2 1/2 hours.

Prior to ordering I removed freezer panel and checked for ice build up and fan functionality. Then removed rear panel cleaned lint from everything pulled front panel vacuumed out the condenser. Plugged back in and all seems to work with the exception of compressor. I have a little experience so googled in model number and your site popped up. I looked up part and the site gave me a percentage loved that. I ordered wish I would have rushed shipping as took about 10 days. Installed in less than 30 minutes and all runs great ??

The toughest part was pulling the refrigerator from the wall....After removing the back-bottom access panel the compressor is right there with the Start-Dev and Cap..Took a few min to remove and install new parts....Very Simple and works great...no more clicking..

I used the computer to enter the make and model of the refrigerator with the icemaker unit. We looked at the diagram to identify the name of the part and then ordered it. It was sent out the next day! We received it and installed it and it works perfect!

It was so easy. I had no idea. My husband and I were directed to your site and we ordered the part with scepticism but with hope that it would solve the problem. As soon as it came in, my husband installed it in five minutes. It was working immediately. Thank you.

this site is invaluable - we searched and came upon it and the schematics for the model of fridge we have allowed us to identify exactly the part that we needed to replace. It was terrific - great site.