6WSC20C6YY00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Paula from Rush, NY
- Parts Used:
- W11384469
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
light switch sticking
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from Beloit, WI
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
Light did not come on (bad bulb!) on TC18KL
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged the unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- daryl from Palm Harbor, FL
- Parts Used:
- WPW10475495
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken rear wheel
I unplugged the unit Frist. Then I removed the grill covering the compressor and fan from the back. I then located the rear wheel and pin. I bent down the retaining tab and removed the pin and wheel. I installed new wheel and pin and bent retaining tab back to origional location. Replaced grill and checked unit for proper operation.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- WILLIAM from Wichita Falls, TX
- Parts Used:
- WPW10335220
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No problem
This was a brand new refrigerator. My wife wanted an additional bin for the fridge door. Thanks for having this and shipping promptly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stefania from miami beach, FL
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
water filter missing
alone
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from The Villages, FL
- Parts Used:
- EDR1RXD1
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Water Filter
Replacing the water filter was no big deal. What impressed me was ordering the filter on Friday and having it at my door on Saturday the next day! That is quality service and I felt you deserve a thumbs up on your customer service skills.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from Pleasanton, CA
- Parts Used:
- WPW10335222
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
No Repairs Required, Added One Bin-Cntlur
Slide into position.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from St. Pete Beach, FL
- Parts Used:
- W11384469
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Broke the arm off the food compartment rocker switch
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Was this instruction helpful to you?
Thank you for voting!