6GD5SHGXSS07 Whirlpool Refrigerator - Instructions

I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me.
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!

Starting at the bottom, with a flat blade screwdriver pry the front cover off the opening. Unplug the wire connector from the back, remove the cover plate holding the switches and light socket by pushing out on the plastic clips on each side. Use something like a bungie cord to hold it up out of the way. Carefully unsnap the clear plastic ice shoot from the push arm, next carefully unsnap the cover door from the push arm. Clean anything that needs cleaning (CLR works great on hard water deposits)
Install everything in reverse order, the cover door first, ice shoot next, switch plate, plug in the wire connector and snap the outside cover in place.

This one is not rocket science, however, it does take some careful "fudging" to accomplish without additional disassembly. The Ice Guide is held in place by three tabs. The tricky part is "tilting" the center tab into it's hole/slot on the ice dispenser lever (center hole), then tilting it up to snap into place.... there is a very tight tolerance here, with the opening of the ice/water dispensing unit. Be sure to "lock out" the ice maker/water dispenser, in order to be able to use the light. Once snapped in place, all is well.

I followed the video exactly, pausing it as I went along. So unbelievably easy! And I’m 78 year old great -grandma! Thank you

This was very easy to install. Part Select had very fast shipping and reasonable prices. I love this website they have everything you need for your appliance. My ice door was very easy to install. I popped it into the grooves on the ice maker. It took about 30 seconds. THANKS PART SELECT YOU ARE GREAT!!!!!! :-)

One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!

1. Put pieces of wood under door to support it.
2. Unscrew three screws holding door hinge.
3. Disconnect water line.
4. Unscrew screw holding each cam. One to door and one to hinge.
5 Replace cams.
6. Retrieve plate with threaded holes behind frame that the hinge attaches to.
7. Use thin philips screwdriver through the hinge bracket, shim, frame and screw plate to align it for the other two screws.
8. Replace all three hinge screws.
9. Connect water line fitting.
10. Remove wood for door support.
11. Check door for smooth movement and strong pressure when closed.

removed door took out single bolt pried out cam put new one in returned bolt rehung door. 15 minutes

pulled old gasket out cleaned area where gasket was and lube edge of new gasket with vaseline starting at top slide gasket in then sides last was bottom which was hardest. 20 minutes

First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!

I changed the bulb but it still didn’t work. I ordered a bulb holder and replaced it and it works properly now. It was an easy repair, remove the bulb, gently pry the bulb holder out with a screwdriver and snap the new one in.

It was useful that under the description of the part in the catalog, it showed that this part was often used to repair this issue. The service was great and the delivery was fast.

First, I removed the 6 screws which hold the ice bin to the drum and the front cover. I then removed the screw which holds the door lever and bracket to the ice bin. Then I took the C clip and washer off the end of the auger to remove it from the housing. I removed the plastic nut to remove the auger drum from the auger shaft, being careful to place the blades on the table in the order they were removed. I then installed the new auger drum on the shaft and re-assembled everything in the reverse order. This was really easy for me because I had replaced the auger previously. (about 2 years ago)

Well - I simply snapped the new shelf into place and vwah la - I have an extra shelf now in our very crowded freezer! Hurray!!!! Super easy.

I just followed the excellent Video for both parts. The door gasket is tedious but doable, just take a deep breath and press on. Putty knife is handy to push edge of gasket under the plastic lip. The closer devices take 3 minutes - simple R&R. Check the videos - they're pretty clear and detailed.

Simply remove the cover over top hinge and remove the three outer screws (Do NOT remove the center screw). Lift the door off the lower pivot pin. Turn door upside down and replace the upper cam and then the lower cam on the pivot at the bottom of the refrigerator case. Reintall the door by setting the door on the lower pivot and then reinstall the top pivot and cover. VERY easy and what a difference. No more "POP".

Purchased the closing cam (both pieces). Removed door (3 bolts under the dust shield on top of door) and replaced the plastic cam pieces. So easy a caveman could do it. I actually had my 13 year old son do it while I supervised!