6GD25DCXHS09 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Both parts were broken and required replacement.
The broken part was removed and new part installed without any trouble.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Murali from Rochester, MN
- Parts Used:
- WP2180353
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Worn out door chute
Pry open the front dispenser outer cover. Remove a screw holding ice door dispenser unit, remove old door chute, remove and place coil kind of stuff (connecting to panel) old chute to new one and reinstall.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Willington, DE
- Parts Used:
- W10823377
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
broker door on ice shute
hardest part was getting up the nerve to pull front cover because it is plastic afraid i would brake it pull from bottom and lift up one screw holds old door inplace uplug electric new door doesn't have electric that it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Cheney, KS
- Parts Used:
- WPW10312300
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Ice container wouldn't dispence
I simply replaced the entire ice container and auger assembly. I intend to repair the old assembly for use as a spare if the new one ever has problems in the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Phoenix, AZ
- Parts Used:
- WPW10321304, WP2156022
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
bottom and middle door bin broke
it snapped right in easy .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew F from Media, PA
- Parts Used:
- W10508993
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The shelf runner broke
Took out the old one and put in the new one. No tolls required. It did give me the opportunity to clean the back wall of the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from Birmingham, AL
- Parts Used:
- WP2188664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My drawer had been broken and I needed a new one.
When I took the pan out of the box, it was not the exact same as the one I had. But it fit perfect. The only hard part was the fact that it looked so good I had to clean the entire fridge side. (Smile)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Corona, CA
- Parts Used:
- WP2182179, WPW10329686
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Wrench set
Worn Down Upper And Lower Cam
Took off refrigerator door from top hinge and lifted off. A little difficulty getting worn out parts off (needed dremel to drill out worn plastic); replaced with new parts, the screw head holding on the part was starting to be worn as well but still worked. If I hadn't got to this repair soon the bottom of the door aluminum would have total worn out as it is, it has a deep groove but not noticeable. The new cams also force the door closed tight instead of slightly ajar at times.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lenexa, KS
- Parts Used:
- W10508993
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Chrisper pan support cracked due to overfilling
removed old shelf support after taking out the glass and support. New part was a perfect fit that was a "shap: to put in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from OPELIKA, AL
- Parts Used:
- W10823511
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
35 year old water tube became brittle and cracked; leaking water
Unscrewed clamp holding water tube to refrigerator ice maker. Pulled water tube from ice maker and water valve inlet. Cut the new tubing to the exact same length and inserted one end to the water valve inlet and the other end to the ice maker then screwed clamp holding water tube back to the refrigerator ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from North Liberty, IA
- Parts Used:
- WP2180224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice chute broke
Just like they told me to do.Insert bottom then sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrea from Cornelius, NC
- Parts Used:
- WPW10321304
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door bin was broken
took old bin out replaced with new , two minute job
Parts select is an easy co. to do business with THANKS Andrea
Parts select is an easy co. to do business with THANKS Andrea
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from North Port, FL
- Parts Used:
- WP2188664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken drawer
replaced
Was this instruction helpful to you?
Thank you for voting!