5ED2FHGXVQ00 Whirlpool Refrigerator - Instructions

Followed Door Removal instructions by removing the Top Screws from the Cabinet. Lifted Door OFF the Metal Hinge. Unscrewed both Lower and Upper Cams from the Hinge and Door. Replaced with new after coating with Vasoline. Lifted Door back in place with help from Wife. Only problem was guiding the Door back onto the Hinge. Works fine. Two year old Frig. This is a design problem, as the cams should last longer than 22 months.

Nothing to do, part came, fully assembled, it just went right into the door. Yea!!!

Took the broken cap off. Actually it practically fell off. Put the new cap in place, turned it to the right and Presto! it locked in and works fine. It took longer to get it out of the box than it did to install it :)

Googled with question about how to get to the repair as there were no screws on the faceplate. Found I had to lift the faceplate at the bottom and pry out. Was kind of hard to get the long spindle back through the ears of the bracket holder along with getting the spring of the door lined up for the spindle to pass through to the other side. Finally got it right and then just put it all back together. Frustrating at first but I had to get it done as my wife was tired of having to take large clumps of ice out of the ice tray..three years wait for the repair. That door being open let warm air in and let the ice melt just enough to stick together in a clump. All is well now. Longer you wait the more appreciative she is however. ha

The repair consisted of lifting up the drawer cover and replacing it. Why the 60 minutes to do that? It took 58 minutes to clean the refrigerator.

took apart panel from door and removed old part and installed new part.It's difficult if you have big hands. Best if you have someone hold up wire panel while you are installing.

It was great repaired the problem for under $60

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

First removed the three screws at the top that holds the door at the top. Removed the worn out lower door cam after removing one screw. Did the same on the door closing cam (in fact this cam has worn and broken into two pieces). Replaced with the new ones, put the screws back, mounted the door and replaced the three screws on top. The door closed perfectly.
Since this did not help with keeping the refrigerator cold, a day later I had to vacuum the dust off the coils (on the underside of the refrigerator) and thaw the ice from the freezer compartment clearing the ducts to re-initiate the proper flow of air between the two compartments (I learnt on the internet that cold air from the freezer is drawn to maintain the temperature in the refrigerator compartment). The faulty refrigerator door ended up icing our frost free referigerator's freezer compartment and the air ducts in it. Therefore I had to simply turn off the refrigerator for 12 hours, thaw everything and restart! I know nothing about refrigerators. Just did it after visiting your site and a couple of other sites. Saved me about $300!!

bought a new crisper drawer

Dismantled the ice bin, and then the ice crusher. I then replaced the auger drum and reversed the dismantle.
I now have crushed ice once again, just like new.
The blow up schematics help isolate the parts needed beautifully. Just like a jobber would expect.
Thanks Guys,

Awesome

Built-in filter was corroded due to age. New filter corrected problem.

Old part would not stay in place (broken). Recieved new part and snapped it in to place . No tools needed.

First, imagine the frustration - I want an apple.... can barely open the drawer. Need carrots - the struggle. Celery? Wondering if I can do without..... the drawer's plastic has broken along where it slides along the guide rails, and it was a pain to open and close the drawer. First, as is my custom I went to Amazon, but couldn't find the part. There, however, I read a useful customer review that told me how to find the correct item, so I did that, input the part number into google, and VOILA - I got to this website. Excitedly, I input my credit card information and waited with eager anticipation (and a bit of trepidation - would it be the correct size?) for the drawer to arrive. A short time later, I found a large box at my front door. With joy, I took some scissors and opened the box, and then carefully used the scissors to cut the binding strap that was holding the protective cardboard wrap. My new drawer!! I gave it a quick clean, and then opened my fridge door all the way (this is an important step). I pulled out the old, broken drawer, and carefully inserted the new. It fit perfectly!! This took about 15 seconds. I then took those apples, carrots, and celery (and a pomegranate and some lettuce) from the old, broken drawer and placed them tenderly into the new drawer. I slid the drawer closed, and then shut the fridge door. Mission accomplished! Last step was to throw the old broken drawer into the garbage - this was a very simple process as well.

We saved hundreds in not calling the service. The ice guide popped right in. As one other person mentioned, took a little force, but no problem. And bin slid in easily. DIY is the way to go these days.

Thanks, PartSelect.com