KTRD18KDWH01 Whirlpool Refrigerator - Instructions

the repair it good and easy ,vo helper to do it.

Instructions came with the part I ordered and they were very easy to follow. Basically you have to remove the cardboard cover from the back. Then you remove the four screws at the bottom (2 front, 2 back) that hold the bottom plate on. My husband tilted frig and held it while I put a block(4" x 1/2") under the bottom outside frame (not the bottom plate). You can see a ridge on the frame which is where I placed the block. My husband braced the frig the whole time I did the repair just to ensure it didn't fall on me even though it was blocked. The bottom plate didn't slide back at first. I took a flat screw driver and hammer and slightly tapped the bottom plate through the screw hole that secures the bottom plate to the frame. I tapped 2 or 3 times...gently each tap...until the bottom plate dropped down. Which was the 1/2" noted in the instructions. I then was able to access the front wheel, remove the pin and replace with the new one. We replaced both front wheels so I did not replace the bottom plate until we replaced the second wheel. We removed the block and tilted the frig to the opposite side, blocked then I replaced the second wheel. Once that was done I removed the block, my husband let the frig down gently and I went to the back and tapped the bottom plate forward. It didn't quite want to go back in place but with patience it finally and then was able to put all screws back in. Donna

took shelf off of freezer, took ice cube maker out, took back panel off changed defrost thermostat.then re-assembled.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

I oringinally thought it was one of the thermostats b/c the freezer started to freeze again after unplugging it. But then the next day it stopped all together and I could hear a clicking noise in the back and the compressor never turned on. It would click at around 2 minutes then again about 17 seconds later. I took photos of the original wires in the connector to match up later. The new parts were not identical to the old. The red wire on the bottom fit fine but the other two wires would not go in the same terminal or numbered positions (1&4). For 2 reasons, 1, the blue female was too small for the male and 2) there was a male missing at position 4. After looking at the guts of the old connector I decided to get new females (2 trips b/c I didn't buy a big enough wire opening - needed 2 wires) and cut, splice & crimp them. I then put the two females on the top two males & plugged it in. No sparks or explosions... but silence. I waited a few minutes and then the fan kicked on and then the compressor started running. That was Sunday, it's now Thursday and things are working well.

poured boiling hot water into drain; removed most ice with hair dryer. Clips(2) positions the defrost tray & drain under the freezer condenser. A "home-made" coil of 18g copper wire inserted into the drain hole, & secured to the defrost heater further prevents the drain from iceing shut!

Fan was barely rotating. So unplugged, removed back cover, removed fan and motor from frame work. Removed fan blade from motor shaft. Spun motor shaft which seemed fine. Pryed off back cover of motor to find a large but dry felt washer and a helical capillery slot formed into the motor shaft for carring oil from felt washer to the bearings. Added 30 wt motor oil and some 3in1 oil to felt and reassembled motor, fan and frame work. Plugged in power chord after getting rid of dust and dog hear on coils and is working like new.

Technically, the repair did not require specialized knowledge. However, replacement of the motor required some effort. Because the motor is located at the bottom of the unit in an area with copper tubing & wiring hindering access it was physically difficult to remove and then replace the motor. A problem arose because the shaft on the replacement motor was larger than the original motor's. Thus the fan would not fit on the new motor. Luckily, I found a fan locally that fit the motor. It would be very helpful if a fan was included in the motor kit. The ref. is now running smoothly

Once I determined easier access to the fan motor, I removed the three fan motor screws that held the motor on place. After removing the motor I remove the fan blade assembly held by one nut and reattached to the new motor. I then reattached the new motor with 3 new screws which were provide and reattached the power cord with the cord clip and began reassembling the icemaker housing, then moved the unit back in place which was installed under counter. I could do this repair in less than 45 minutes now that I have done it once. I saved several hundred $ from the original estimate and the parts were delivered in 2 days after I ordered online. This is definitely a DIY project!!

1.Slid out old cracked drawers 2.Slid in new crisper drawers Simple! It took longer to open the shipping boxes than to install the new drawers! Problem solved! If only all fixes were this easy!!

Viewed the viedo - it showed what to do

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

The instuctions say take the door off. I didnt find that necessary. Made sure the new gasket would fit. Pulled the old gasket out inline with the door instead of away. The gasket came off like an innertube on a bicycle. Installation of my new gasket was easy. I started on a corner hooking the lip behind the ledge and worked my way around the door. 10 min maybe. That's it

Removed glass shelf. Removed both crisper bowls. Removed broken rail and put new rail in! Hardest part was taking out all the items sitting on the glass shelf. Actual installation time under 1 minute.

Ordered new drawer. New drawer seems to be better than factory drawer (slightly thicker). Removed old, removed white handle from old (ran hot water over old to make it less prone to cracking when prying off), pushed old white handle onto new drawer, inserted new drawer, done. New drawer is great; better construction. Thanks.