3XES0GTQNL00 Whirlpool Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jennifer from Birmingham, AL
- Parts Used:
- WP2188664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My drawer had been broken and I needed a new one.
When I took the pan out of the box, it was not the exact same as the one I had. But it fit perfect. The only hard part was the fact that it looked so good I had to clean the entire fridge side. (Smile)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Melvin from OPELIKA, AL
- Parts Used:
- W10823511
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
35 year old water tube became brittle and cracked; leaking water
Unscrewed clamp holding water tube to refrigerator ice maker. Pulled water tube from ice maker and water valve inlet. Cut the new tubing to the exact same length and inserted one end to the water valve inlet and the other end to the ice maker then screwed clamp holding water tube back to the refrigerator ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Lenexa, KS
- Parts Used:
- W10508993
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Chrisper pan support cracked due to overfilling
removed old shelf support after taking out the glass and support. New part was a perfect fit that was a "shap: to put in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jay from Sarasota, FL
- Parts Used:
- WP2180226
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice dispenser auger would not rotate and drop ice
First, I replaced the auger motor at a cost of $87.00. That job took about 15 minutes and was very easy, but it still didn't work. So, I took off the front panel that covered the ice/water dispenser controls and some white plastic parts rained down out of it. I then discovered the problem was the mounting points that held the ice dispenser switch in place. The $13.00 white control bracket fixed the problem. Should have checked this first, as I later learned that the motors rarely go bad.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- anthony from georgetown, IL
- Parts Used:
- WP628356
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Broken Piece
Had to disassemble ice maker to install part. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cathy from North Liberty, IA
- Parts Used:
- WP2180224
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice chute broke
Just like they told me to do.Insert bottom then sides.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- elisa from richlands, NC
- Parts Used:
- WP2187172
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken Door Bins
Placed bin on the door and done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Paul from NAYLOR, MO
- Parts Used:
- WP2188664
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crack in vegetable drawer
Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Clearwater, FL
- Parts Used:
- W10823377
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Chute Mechanism broke / air flow into ice maker
Have not installed yet as I'm on a quick TX-FL-TX turnaround. Bought and received the part in 24 hours...great. Order contained no instructions. I could probably figure it out myself just have not attempted yet.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from North Port, FL
- Parts Used:
- WP2188664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken drawer
replaced
Was this instruction helpful to you?
Thank you for voting!
Crisper crac kerd and there was no glass insert cover
It took me less than 5 minutes and I had everything installed myself. thanks for the help in ordering the right parts
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Albuquerque, NM
- Parts Used:
- WP2180224
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice Guide broke during cleaning
Part would not fit straight in. Used universal joint on end of extension to reach screw rather that disassemble front. Managed to slip the paddel just far enough to one side and angled to snap ice guid on and then slipped paddel back into place. Used a dab of candle stickum on the screw head to heep it in the socket and then inserted in door. $7 part, 15min and saved $$$$$$ over a service call;)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheila from Lena, MS
- Parts Used:
- 4388736
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice Maker would no longer move ice through the dispenser
As cookbook authors and publishers, my husband and I depend on our appliances. When our icemaker would no longer work, it was imperative that we repair it as quickly and ecomonically as possible. We had used PartSelect.com earlier to order a part to repair our Jenn-Air stove top and had great results. So, rather than paying a repairman four times or more the cost of the part, we ordered the part and my husband installed it. It took less than 30 minutes to remove the broken auger and install the new one. THANKS PartSelect.com -- we'll use you for all appliance parts needs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Mt Juliet, TN
- Parts Used:
- W10823377
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Plastic door bracket for icemaker chute broken
Googled with question about how to get to the repair as there were no screws on the faceplate. Found I had to lift the faceplate at the bottom and pry out. Was kind of hard to get the long spindle back through the ears of the bracket holder along with getting the spring of the door lined up for the spindle to pass through to the other side. Finally got it right and then just put it all back together. Frustrating at first but I had to get it done as my wife was tired of having to take large clumps of ice out of the ice tray..three years wait for the repair. That door being open let warm air in and let the ice melt just enough to stick together in a clump. All is well now. Longer you wait the more appreciative she is however. ha
Was this instruction helpful to you?
Thank you for voting!
My Crisper Draw side railing had broken
I ordered the 2 new drawers, the crisper pan and the meat pan with handle. I took them from the box, wiped them out and slid them right into the spots where my previous drawers were. End of story. This took less than 5 minutes to install. I used the chat feature to inquire as to what number items that I needed to order these 2 drawers, was given the numbers and order the items on line right then. Easy They arrived in record time, like maybe 2 days. They were well packed and arrived in pristine condition.
Was this instruction helpful to you?
Thank you for voting!