3VET21DKAW00 Whirlpool Refrigerator - Instructions

Remove inside door trim plate. Then removed three screws that held in the light assembly. The only difficult thing was reconnecting the temperature adjustment rod. After replacing this rod you must slide the temperature control slide to midway and this hold the rod in place while reinstalling the light assembly. If I were to do it again it would probably take me half as long.

Pulled up part select video on u-tube. Followed instructions on dissambly of top freezer and found condensor freezing up blocking air from refrigerator. Checked timer to make sure it was good. Next checked continuity on heater to make sure it was good. Last checked bi-metal thermostat for continuity while cold. Found Bi-metal part to be defective (also rubber in top of was popped up which is a sign of a bad part). Simply ordered new part from Part Select, received in 2 days and replaced Bi-metal and melted ice with hair dryer and reassembled freezer. While waiting on part you can still use refrigerator by melting ice so air can get to refrigerator. I put a towel in bottom of freezer to catch water. Greg W. in Ga.

This problem can be caused by 3 different part failures. Timer, thermostat or heater. After contacting a service repair shop I was told that most often it is the thermostat. The cost of the repair would be at least $115. To much for an old refer. So I ordered the part from Partselect for $33. and put it in myself. Step1 cut the power to the refer. Step2 remove ice maker if you have one. Step3 remove base and back panels in the freezer. Step4 the coils were badly frozen so I used a hair dryer to thaw it out. Would have waited a long time for it to thaw out otherwise. Step5 The thermostat is clipped on to copper tubing next to the coils. Unclip it and cut the wires close to the thermostat. Strip the wires and wire nut the new thermostat. Clip it back on to the copper tubing. Put it all back together and start it up. It's over a week know and no problems. Note: We have whirlpool appliances that are over 16 years old. I have repaired the washer, oven, and now the refer with parts from Partselect. Good company. Always received the correct part within about 3 days from ordering. If you are able to do the work yourself you can save big bucks and keep your appliances running longer. Good Luck

The fix was easy. I jacked up the unit and put on blocks. I used socket and ratchet removed the wheels. Reinstall new ones and let off the blocks.

unscrewed the broken part of the handle and put the new one on. It was easier than expected.

I wasnt about to call Mr Appliance of Bayport NY the last time I called him I got a bill for $72.00 and he told me I needed a new frig. So I paid him then the next day I went to parts select and fixed it myself for about $50.00 But this time it was my Moms frig and the frig side (fresh food side) wasnt getting cold So again I went to parts select and put in a bimetel thermostat and it works perfect now. Im sure I saved a lot of $ and thanks to parts select, They helped me diagnose the problem and make the repair step by step! EASY! Thanks parts select...Garry from long island NY

We followed de video that made it very clear to us. Thank you! It's been working great since...

Just instaling the new part with a screw driver

Removed items and defrosted freezer. I then removed metal shelves, ice maker, bottom sliding tray and false bottom, freezer back, and light bulb with wire track. Cut wires to defrost thermostat and spliced in new thermostat. Reassembled shelves, back, etc., in reverse order. Old thermostat tested "open" in hot and cold water with Ohm meter tester.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

First, although I was SURE I knew what to do, I watched the repair video. I used needle nose pliers to push broken support into wall since I could not pull it out. Selected correct wall fixture, spread holder pins, and snapped into wall opening. Couldn't have been easier!!! Very useful site.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

Cover the entire metal retainer bar in painter's tape (the blue one) and use a 20-22" hacksaw to cut it to the correct length, going very slowly in your sawing.

This repair was super easy. there are only 5 screws to remove to get at the defective switch. 3 in the housing where the light bulbs are and 2 in the front trim piece where the cooling adjustment dials are. I never did unplug the fridge ,but probably should have although nothing bad happened. I removed all 5 screws using a 1/4" socket ( a nutdriver would work well also). there is also a small dia rod that comes down from the coolness adj. wheel that when you re-assemble goes though the middle of the wheel. The switch has only 2 wires that clip on with the push on flat type connectors. Very simple. I removed the wires and then the switch can be removed( it is only held in by 2 squeezable side clips). I put the new switch in and connected the wires , checked to see that the lights went on and off. which they did. then just put the screws back in.....done. also I would like to say that when I ordered my switch it came super fast. I ordered it online at 11:00am on a tuesday and it was on my doorstep in wisconsin by 10:00 am the next day...Thanks

Replaced bracket-amazed to find how quickly I was able to id the part on this 20 year old refrigerator. Ordered the part and received it the next day! Thanks for the good service! , Bob