ED5JHAXML00 Whirlpool Refrigerator - Instructions

Removed plastic door over ice maker remove 4 screws and slide unit out after disconecting pull apart elect. Plug. Pop off side gear cover install on new and slide in, reconnecting electric plug as you go.

I ran all the ice maker module tests that I could find online, I tried cleaning the contacts inside the ice maker control module, nothing worked...so I finally decided to purchase a new control module. I had already had the module out and taken apart a few times, so the new one was very easy to install. Just removed the entire icemaker from the fridge, removed a few screws, took off the old module, put on the new one, replaced the screws, re-installed the icemaker in the fridge (it just slides in and out similar to a shelf). And 30 minutes later I heard the first batch of ice cubes drop! And by morning the bucket was nearly full. After two weeks of no ice and trying to fix it myself - the family was glad to have ice again (it was July in NC!). In retrospect, I should have followed the advice I found online and ordered the new part sooner and saved all of those frustrating hours of trying to "fix" the part myself.

Removed cardboard back from refrig. Found source of smell/burn. Removed part. Ordered several replacement parts as the diagram was not clear as to which part would be needed. New parts arrived, matched with old. Cleaned carbon from contacts, installed new part. Cleaned dust from refrigeration coils, installed back. Returned unused parts.

The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

removed the clip that the motor was attached too put the new motor back on reinstalled the clip back on the fridge plugged the wire harness in and works perfect now . it was easier to remove the clip than to try to install the motor by itself its just to tight and you cant get in there

Remove the kick panel and simply turn the filter counter clockwise and it slips right out.Water shuts off when filter is removed.After new filter is installed be sure to bleed line thru the water outlet in door to clear air in system.When first water is bled the water will continue to run until line drains. Then comes the air.Bleed until water is clear.Its an easy job and can save you$$$$$.Ray Palm Bch Fl.

Replaced 8 cube ice maker assembly. Contrary to instructions I 1st removed 2 screws on the flapper door 2 removed 3 screws in bottom and 1 screw on right side bottom and pulled shelf out unplugged plug and lifted assembly off put new one on shelf plugged it in and slid it back into place replaceing. screws. was done in 10 min. start to finish . so far seems to have solved the problem.

Linkage on the cold-control mechanism in the air diffuser assembly was broken. It was necessary to access the diffuser assembly from both the refrigerator and freezer sides of the unit.
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now.

Taped plastic cover to get it out of the way with duct tape - removed three screws on each side - removed retaining screw for each module - carefully disengaged module using small flat head screw driver being sure to release the plastic retainer and then reverse the process. Be sure new modules snap into place.

Biggest problem was initially figuring out what the problem was. Turning off the ice maker had no effect and it just kept making ice.

It was really easy to do. The water filter is in the front of the refrigerator. Less than 30 seconds. I am very happy with PartSelect. I bought parts for my dryer too. New lint filter, timer knob and door handle. Parts arrive immediately. I am sure I will be back to PartSelect.com.

Emiter blinking red; ice maker stopped working. Called appliance repair, said electronic control boards needed to be replaced. Quoted me $275, including parts. Ordered part at partselect.com, installed in 15 min and ice maker started producing ice. Also discovered on other online forums that this part is a common failure on these model refrigerators. Very easy to swap out, plug & play. Make sure to unplug appliance before performing repair due to shock risk.

Pulled out the old drawer and put in the new.

I replaced the Crisper Pan with no problem. The snack Crisper Drawer doesn't come with the white trim, so you have to take it off the broken drawer and put it on the new one. I think removing the trim & putting it on the new drawer was the most difficult part since it is such a snug fit! Still, it only too a couple of minutes. Now I am wondering why I waited so long to order new drawers!! Thanks Parts Select!

Well I changed out the optical boards which I thought were the problem and the ice maker is still not making any ice. I can see the ice makers fingers rotating but there is no water entering through the tube. I jumped the water manifold in the back and water comes out but I cant figure out what is not telling it to run water and fill the ice tray. Any ideas would be appreciated I guess i'll replace the ice maker next. Thanks in advance.

Removed face plate, disconnected wires, removed and replaced micro switch and control bracket.