ED2FHEXSB05 Whirlpool Refrigerator - Instructions

I discovered recently that the grille was removable. The protective coating had been removed because of using a scrub brush to remove hard water stains. It looked horrible and was very hard to keep clean. The new one works fantastically!! No tools required at all. I feel stupid not having done this sooner.

I discovered that the freezer was not defrosting automatically and the condenser coil was freezing up blocking the flow of cold air to the refrigerator side. I first replaced the thermostat thinking that it would be an easy fix but needless to say it didn't work. My indicator that it was not a successful repair was the continuing blinking of the filter change light on the control panel. Ultimately I had to replace the control board assembly to solve the issue.

Initially I removed the cover to the auger and auger drum. Then the split ring locking washer had to be removed. I used a needle-nosed pliers and small screw-driver to pry that off. The auger arm could then be removed, and the auger blades removed. This proved to be the part that required the most patience. The blades need to removed and returned in their exact pattern. Someone else suggested taking a digital picture of them before removing them; this is a good suggestion that I failed to do. Once the blades are returned, all the other parts can be replaced in reverse order. Put the screws back in, and you are finished.

I just removed a few screews and took the cover out of the ice box. Put my voltage meter to the refrigeator and realized the the unit was not defrosting...I then got the part number and entered it in on your web site. A few days later my part arrived. I put the part on and in just about 20 minutes I was up an running again...Thank you Part Select for fast and great service. I own 35 rental properties and having a online appliance parts store really saves me a lot of time and money.

Thank you
Curtis Hall

Disconnect power to refrigerator. Removed all food from Freezer. Removed all Shelves and shelf clips. Used phillips screwdriver and removed 6 screws from lower rear panel covering evaporator coil. Removed panel. Pulled plastic fan blade off top of motor shaft. Unclip top front of black motor retainer clip which then allowed the rear clip to unhook. Removed clip. Then removed 3 wires from fan motor, noting proper location for replacement. Slide the fan motor out to the left. Installed new motor. Reinstalled clip, hooking rear side first. Then rehooked the 3 wires. Slide fan blade back on top until secure. Tested everything at this point before reassembling rear panel. Then replace rear panel, replace the 6 screws, replace shelf clips and shelves and replace food. Very easy to do and saved about $150 over a service call to troubleshoot and re-visit to install after getting part

First remove the ice container from the freezer
and dump all of the ice. Remove the four
screws holding the front ice container cover. Remove the control arm screw and bracket from the bottom of the ice container, remove crusher housing (screws and retainer clip). Remove nylon
bearing nut on front of auger shaft (left handed threads). Remove crusher blades and spacers (remember order of blades and spacers). Remove broken floating baffle. Replace baffle and reverse removal procedures.

Dog chewes up the original part. Got the replacement , put it on the filter turned to lock in place and tried tp pull out old filter ( same procedure has been done multiple times successfully) part broke instantly upon putting pressure tom pull out filter. Sent back to you the next day for replacement.

Removed the icemaker to see if I could determine problem; motor was seized; got part numbers and ordered from you; parts arrived next day (even though overnight delivery wasnt' requested - so THANK YOU!); compared new parts to original to be sure of fit; reassembled unit; reinstalled in freezer, and waited for the sound of water filling the tray. Producing like brand new again! Cancelled the service call w/ Sears for the following week (when it was convenient for them) Loved your service!

The hardest part was getting the front cover plate off. I used two kitchen knifes one in each slot on the bottom of the plate and pried it off and unplug it. I removed one screw to release arm. I then used long nose pliers to remove the pin on door arm assemble. Then unplug door heater. New door has no heater. The heater had cooked the plastic arm, which caused the arm to fail. Then reassemble in reverse order.

Pulled out the old drawer and put in the new.

Linkage on the cold-control mechanism in the air diffuser assembly was broken. It was necessary to access the diffuser assembly from both the refrigerator and freezer sides of the unit.
Re-connected the linkage between the diffuser and cold-control assembly; remounted the two combined assemblies . . . refrigerator working nicely now.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Followed instructions supplied. It was relatively easy and the parts fit exactly right. Sears wanted twice as much for the part and service would have charged me another $100 to come to my home. I saved over $100 doing the project myself.

I replaced the Crisper Pan with no problem. The snack Crisper Drawer doesn't come with the white trim, so you have to take it off the broken drawer and put it on the new one. I think removing the trim & putting it on the new drawer was the most difficult part since it is such a snug fit! Still, it only too a couple of minutes. Now I am wondering why I waited so long to order new drawers!! Thanks Parts Select!

Removed face plate, disconnected wires, removed and replaced micro switch and control bracket.