3XART700F01 Whirlpool Refrigerator - Instructions

snapped the new shelf retainer end caps onto one new trim-door and 2 old ones and snapped all 3 back onto the freezer door above each shelf so I can now use 3 freezer shelves

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

Very simple fix, remove 3 screws, two connectors to the old switch

Just followed the video supplied with shipment. 5 minutes, even for a mechanically-challenged person.

Removed cheese & cold cut drawer accessing lower crisper drawer glass missing from surrounding frame.
Dropped in glass into grove of crisper frame…Reinstalled (sliding)!above cold cut drawer in its position and the same for crisper drawer..Finished!!!
All good except for $110.00 price tag for a piece of glass

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Purchased the closing cam (both pieces). Removed door (3 bolts under the dust shield on top of door) and replaced the plastic cam pieces. So easy a caveman could do it. I actually had my 13 year old son do it while I supervised!

easy - remove the door, replace th part, put back the door

Undo a few screws on top of door, replace closing washers at bottom part of door, put door back on, and done. Easy. Just make sure you have the top and bottom closer washers that go together...2 parts.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Slid the old drawer out and slid the new drawer in. Less then a minute!

Simply remove the cover over top hinge and remove the three outer screws (Do NOT remove the center screw). Lift the door off the lower pivot pin. Turn door upside down and replace the upper cam and then the lower cam on the pivot at the bottom of the refrigerator case. Reintall the door by setting the door on the lower pivot and then reinstall the top pivot and cover. VERY easy and what a difference. No more "POP".

I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!