EB22DKXFW01 Whirlpool Refrigerator - Instructions

figured out the condenser fan was kaput. Tried WD, worked for several days then gave out completely. Took off back of fridge and trained small fan on compressor while I ordered new condenser fan. The swap was easy, undid the housing bolts, stripped off the connector, reconnected and voila! works perfect.

I simply used my cordless drill with the right sized socket attachment to remove the screws. I left the door on which wasn't as difficult as I thought after reading other stories. I even had to contend with my three year old who wanted to know what was going on and if she could help. As my wife is deployed it falls to me to become both parents, watch after her and take care of chores. With all that said it still only took me about half an hour to replace the old gasket with the new one. As far as the gasket goes I wish the magnet was more powerful because there is still a gap unless you push and hold it closed for an extra second when closing the freezer. A pain but at least it is not torn. Before buying I recommend searching for a parts/service center that that talks about the whole part not just how to replace.

First we read all the comments by other handymen. This was really helpful. Then we took the door off and removed the old gasket with a nut driver. We tried to slip the new gasket under the edge with a thin spatula and didn't have much luck. Then we remembered someone saying that is was a good time to take the door apart and check to see if there was ice build up in the door. It was so bad we took out the frozen insulation and replaced it with new....$4.00 at the hardware store. While the door was apart we put the gasket on and put it in place and tightened it to the door. This worked very well for us. This saved us from having to buy a new refrigerator/ freezer. Thanks.

I loosened(but did not remove) the 1/4" sheetmetal screws around the perimeter of the door liner. (they are numerous and they are hidden in the fold of the gasket) I removed the old gasket. With the screws still loose, I installed the new gasket. After insallation I re-tightened the liner screws. Several gaps were noted and eliminated by gently heating the gasket with a hair dryer. (be patient , it takes some time)

There were no instructions with the new gasket which made the job difficult. After great difficulty I called an appliance store and learned that the gasket should be soaked for several minutes in very hot water to make it pliable and easier to install. Also, the plastic insert that the gasket fits into should only be loosened and not removed when inserting the gasket. Lastly, the door should be removed and placed on a table to allow leverage to be applied. Installing it while still on the door is almost impossible.

replaced water valve and new icemaker.

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well

Started with internet searches then began with removal of wall plate at back of freezer, pulled power cord first. Found evaporator coil completely frozen over.Went back to internet and searched possible causes. It seemed to me that the auto defrost system may not be functioning properly so I considered possible causes. Defrost thermostat, defrost timer, or possibility heater itself. I chose to go with simple stuff first and thought heater would have a better relibility characteristic. Went to Parts select got part numbers and was able to find part locations on the appliance. So far so good, and knock on wood! Thanks Parts select I spent $50 bucks instead of $1000.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

Removed screws to pull the part out and took fan off. Put fan back on the new part and put it back in place. Runs very quiet !!!

Thanks !

carefully

1- Remove food from freezer and store in ice chest
2- Turn off refrigerator
3- Remove freezer drawers, 2 drawers, no fastener
4- Remove freezer slide out drawer front , 2 screws
5- Remove ice cube tray holder, 2 screws
6- De-ice back panel with hair dryer / blower
7- Remove back panel in freezer, 8 screws
8- Defrost refrig coil with hair dryer / blower
9- Unplug Bimetal Thermostat, 2 wires, orang / brn
10- Remove Bimetal Thermostat from coil, 1 clip
11- Install new Bimetal Thermostat
12- Re-assemble, reverse order

remove ice maker vent and back piece. Unclip defrost thermostat and unplug. Plug new thermostat in and clip to element, reattach back piece, vent and ice maker. Is a tight fit getting icemaker out, there are 3 screws 2 on top and one on bottom.

I had to cut a groove in the bushing to put the elec. wires through it, & then just remove the hinge, put the bushing in & replace the hing.

First let me say the part arrived much faster than I anticipated! I was able to use the box (cardboard) the part came in to cover the freezer while the door was being worked on. I did not remove the door, but did remove all the screws that held the door inner part that the gasket fits around. Like another person wrote, my insulation in the door was frozen. I took that out and put new insulation in. I then fit the gasket around it and then screwed it back on. I have an electric screw driver and without the bit, it fit these hex screws perfectly, so I was able to unscrew and screw quickly.

Unfortunately, I realized the cause for the dripping was due to a faulty defrost thermostat. I'm guessing that part will arrive tomorrow. We did need a new gasket, however, so I don't regret it.