EL7ATRRKQ00 Whirlpool Refrigerator - Instructions

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

Removed one of the retainer nuts, slid the shaft into the new roller and replaced.
Hardest part was getting a friend to balance the refigerator leaning forward while I did the changeout, and the friend had the hard job.

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sincerely, Ron Marshall, Billings, MT

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

First filled tub with hot water and placed new gasket in water to limber up. Removed Door, placed on a table, removed all screws and removed door insides and old gasket, Cleaned all parts, dried new gasket then put back together just in reverse of removal, moved fridge back into place turned back on and it was cooled back down in about 15 min. working great. Now it has the same vacuum on it as when it was new.

put the new gasket in a tub of hot water. remove door and lay on flat surface, remove old gasket and pull hot gasket from tub, dry and install, the hot water helps remove the wringles from shipping.

Removed door. Laid door down on a table. Unscrewed all screws around outside of door. Removed plastic cover back of door underneath cover was filled with heavy ice apparently from condensation. Cleaned and dried back of door really well. Replaced with new seal. Reinstalled door. New seal works perfectly.

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

I unplugged and defrosted the freezer ( good excuse to give it a good cleaning). I then removed the hex screws from the door under the gasket. Because this attaches the door panel to the freezer, it is helpful to have two people for this task if you have a full size upright freezer. We then removed the panel, cleaned the door, and fitted the new gasket in place. If your gasket has kinks in it, either throw it in the dryer on low for a few minutes or use a hair dryer to smooth them out. We then added a few screws around the center point of each side to hold the gasket in place, secured the corners, and replaced the remainder of the screws. We used a small cordless drill. The gasket will be hard at first, so I duct taped the freezer door shut with a few pieces of tape and turned the unit back on. A repair guy was going to charge me $350.00 for the job, but I did it for free with the cost of the gasket. This site is the least expensive place I found anywhere, and shipped very quickly!

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th