3XARG477GF02 Whirlpool Refrigerator - Instructions

Repair was very easy. We removed the glass from the shelf above the crisper drawers and then just snapped the rail into the frame.

Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.

The instuctions say take the door off. I didnt find that necessary. Made sure the new gasket would fit. Pulled the old gasket out inline with the door instead of away. The gasket came off like an innertube on a bicycle. Installation of my new gasket was easy. I started on a corner hooking the lip behind the ledge and worked my way around the door. 10 min maybe. That's it

Removed glass shelf. Removed both crisper bowls. Removed broken rail and put new rail in! Hardest part was taking out all the items sitting on the glass shelf. Actual installation time under 1 minute.

Hardest part is putting in the replacement ice maker. this is easily resolved if you have a 3x5 mirror. The mirror allows you to see where the screws are and place your 1/4 inch socket. The replacement part was identical to the original so did not need to replace wiring and other items included in the package received.

My grandson did all the installing, he is really good at anything he goes to install, needs to look into something for him in this catagory, he said instruction sent was really easy to understand, will order from part select again. Thanks!

After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.

removed the lower door. took out the old gasket, snap in the new one. piece of cake.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.

Followed the very easy instruction that came with kit. Even a partially trained Monkey could do it with the easy instructions. very satisfied. Had Ice in about an Hour.

Went to various websites looking for guidance. Finally went to PartSelect since I had previously purchased dryer parts. I entered the model info, etc. from my refrigerator and ordered the ice maker installation kit. The install was fairly easy and everything worked perfectly. I am very satisfied I could do the work myself versus calling a repair technician.

Ordered the complete ice maker kit because I wasn't sure which part went bad. I replaced the ice maker assembly first which was very easy to do. I couldn't tell if the new ice maker was doing anything. I waited almost 16 hours before the ice maker started to run and make ice. I would just say to be patient after installing these parts if you don't immediatly see anything happening. Saving the solenoid and other extra parts if needed in the future.

Looked up the refrigerator model number, found parts break down and ordered wheel assy...thought it was the wrong but wheel size was right...read the instructions (good thing) and found out you had to slide entire bottom panel out 1/2 inch to access a hidden pin...did as the instructions said, slid out the bottom panel, found pin as advertised, removed pin, broken part fell out, replaced the wheel assembly, repinned, slid the bottom panel in (a bit more harder than getting it out), replaced all screws and was completed in about 40 -50 minutes. Good thing it came with instructions!!

I was pleased with the new ice maker and how soon I received it. I was disappointed because there were NO installation instructions that came with it. There were only service instructions that came with it. I contacted partselect and was told that they get the part from whirlpool and they are responsible for everything and was given a phone number to call. I called Whirlpool and was informed that they don't provide installation instructions, I said that on the web page is boldly displayed an installation instruction sheet. Whirlpool said that they expect that the installation person knows what they are doing. I let it go and was very careful taking the old one out and installing the new ice maker and the new pump.