4YED20TKDW00 Whirlpool Refrigerator - Instructions

Followed instructions that were online when ordering part. Put a adjustable wrench on the square end of the plastic support and twisted upward. Support bracket came off easily. Inserted new part and twisted downward on the square end of the support and it locked in place. Surprised it was so simple.

remove door, replace cam, replace door

Simple read about three of the other peoples repairs,did the same and (PIECE OF CAKE)
Only problem ordered the cam kit with shipping over # 18.oo and only needed two pieces to do the job. Should have ordered just the two cams and saved a lot of dough.
But done and over with a happy camper (WIFE)

Placed tray on lower part of refrigerator.

Popped out the old, popped in the new. . . Good to go in about 30 seconds. . . . Felt cheated it was so easy. Problem solved.

watched your instructions

Pulled out the old ones and put in the new ones.

I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!

I follow the video From The Tech Guy ( Gentleman ). Thank you... Best Regards .Fco

just as the installation video show (very helpful) however the sheath tube that was pulled off of the old capillary tube did not go back on the new tube near as easy as the video showed. Got it on however and refrigerator is working like a champ now

I read a previous entry that stated the stud needed to be twisted out, which was very useful. I was bit worried at first when I removed the broken one and a bit of the insulation came out and it seemed mangled inside, but twisting the new one in worked. It is in there firm and strong, good as original.

Removed all of the food from the door by lifting the shelves out. Unbolted the top door hinge, and lifted the door off. Replaced the cam and placed the door back on, re-bolted the top hinge and placed all of the food and shelving back into the door. The door closes and seals when it is shut.

Followed the video instructions.

Remove one 5/16 screw from top hinge cover plate. Trace outline of hinge on top of refrigerator with sharpie, so you will know where to put hinge back. Remove 3 5/16 screws from hinge. Lift door up out of bottom hinge, place on table to be able to work on. Remove one 5/16 screw and upper cam piece from bottom of door and replace with new upper cam piece. Remove one 5/16 screw and lower cam piece from bottom hinge on refrigerator. Replace with new lower cam piece and one screw Set door back in place and reattach top hinge with 3 screws adjust refrigerator door as needed for a nice even gap between freezer and refrigerator doors. Tighten screws down and put hinge cover back on with one screw.

Following the instructions on the site I removed the upper hinge cover and hinge(after removing the shelves from the door). I replaced both cams on the bottom hinge, reinstalled the door and the problem was solved. A couple of hints that may speed up the process: 1. On installing the door cam, I didn't get the holes in the door and cam aligned well due to a bit of interference from the metal tab on the door, so I temporarily inserted the upper hinge pivot in the bottom hole and retightened the cam. 2. I decide to re-align the freezer door . After this, the ice and water dispensers didn't work. Turns out the internal freezer light switch which also acts as a cutoff switch for the door dispensers wasn't being activated. Easy to adjust once the cause was discovered.